Abstract:Among fuel cells, the direct methanol fuel cell (DMFC) has attracted great attention and has been considered a very promising power source because of the ease of methanol transportation and its high energy density. A major limiting factor hindering DMFC’s commercial application is the poor catalytic performance in the anode (methanol oxidation reaction). The methanol oxidation reaction (MOR) requires (OH-) from water dissociation as an oxygen donor for the reaction; however, the slow water dissociation on Pt limits the rate of MOR. In addition to the sluggish catalytic activity, the other major impediment for Pt catalysts is the generation of carbon monoxide (CO) during the MOR process.In order to improve the catalytic performance of MOR catalysts, a variety of catalyst design strategies have been devised. The interesting way of carrying out the MOR catalytic process is the non-CO pathway which takes place on Pt-Au bimetallic catalysts, thus eliminating CO poisoning. However, the overall activity of Pt-Au alloys in MOR is relatively low, which ultimately limits the application of Pt-Au catalysts. In this study, a nanoporous (np) Au-Cu-Pt thin-film catalyst with a fine structure and tunable composition is synthesized by using a facile method involving successive electrodeposition and de-alloying. SEM, SEM-EDX and ICP have been used for morphology characterization and composition assessment. Pb under-potential deposition (UPD), H UPD and CO stripping tests have been employed to determine the electrochemical active surface area (ECSA) and to probe the Pt active sites specifically. Also, cyclic voltammetry (CV) tests have been performed to assess the catalytic performance in MOR. Finally, long-term CV and chronoamperometry (constant potential) tests have been used to study and evaluate the durability of accordingly synthesized catalyst for MOR. The prepared np Au-Cu-(8% in the precursor alloy)Pt catalyst exhibits outstanding mass and specific activity toward the MOR, which is approximately six- and nine-times higher than the activity of a commercial Pt/C(40%) counterpart, respectively. A negative 75 mV onset potential shift upon the MOR anodic scan on the np Au-Cu-(8 %)Pt catalyst in comparison with Pt/C(40%) corroborates its higher catalytic activity. Furthermore, the alloy catalyst demonstrates better durability than the Pt/C(40%) counterpart in a three-hour constant potential test and exhibits full post-factum recovery of its cycling activity. In addition, it retains more than 60% of its original activity after 3000 cycles of an accelerated degradation test. Reference: Xie, Y., Li, C., Razek, S.A., Fang, J. and Dimitrov, N., 2020. Synthesis of Nanoporous Au− Cu− Pt Alloy as a Superior Catalyst for the Methanol Oxidation Reaction. ChemElectroChem, 7(2), pp.569-580.

Antimony-Doped Tin Oxide Nanofibers as Catalyst Support Structures for the Methanol Oxidation Reaction in Direct Methanol Fuel Cells

Highly Active Nanoporous Pt-based Alloy As Anode and Cathode Catalyst for Direct Methanol Fuel Cells

One-step synthesis of antimony-doped tin oxide/multi-walled carbon nanotube composites: a promising support for platinum catalysts in a direct methanol fuel cell

Pt Supported on Carbon‐coating Antimony Tin Oxide As Anode Catalyst for Direct Methanol Fuel Cell

Effect of Sb-Doped SnO2 Nanostructures on Electrocatalytic Performance of a Pt Catalyst for Methanol Oxidation Reaction

Fine-tuning the Cross-Sectional Architecture of Antimony-doped Tin Oxide Nanofibers As Pt Catalyst Support for Enhanced Oxygen Reduction Activity

Nitrogen-doped carbon black supported synergistic palladium single atoms and nanoparticles for electrocatalytic oxidation of methanol

Aqueous Synthesis of Au10Pt1 Nanorods Decorated with MnO2 Nanosheets for the Enhanced Electrocatalytic Oxidation of Methanol

Methanol Oxidation at Platinum Coated Black Titania Nanotubes and Titanium Felt Electrodes

Nanoporous Au-Cu-Pt As a Superior Electro-Catalyst for the Methanol Oxidation Reaction

Ultrathin PtNiGaSnMoRe Senary Nanowires with Partial Amorphous Structure Enable Remarkable Methanol Oxidation Electrocatalysis

Pt-Decorate MOFs Derived Ni-N-C Materials as an Efficient Electrocatalyst for Methanol Oxidation

Fabrication and Characterization of New Composite Tio2 Carbon Nanofiber Anodic Catalyst Support for Direct Methanol Fuel Cell via Electrospinning Method

PEDOT-embellished Ti 3 C 2 Tx nanosheet supported Pt–Pd bimetallic nanoparticles as efficient and stable methanol oxidation electrocatalysts

PtRu Catalysts on Nitrogen-Doped Carbon Nanotubes with Conformal Hydrogenated TiO 2 Shells for Methanol Oxidation

Facile Synthesis of PtP2 Nanocrystals As Highly Active Electrocatalysts for Methanol Oxidation.

Pt/CN-doped Electrocatalysts: Superior Electrocatalytic Activity for Methanol Oxidation Reaction and Mechanistic Insight into Interfacial Enhancement

TiO2 Nanotube-Carbon (TNT-C) as Support for Pt-based Catalyst for High Methanol Oxidation Reaction in Direct Methanol Fuel Cell

N-doped titanium oxide/carbon composite as supports for platinum catalysts in highly efficient methanol oxidation

Facile synthesis of trimetallic PtAuCu alloy nanowires as High−Performance electrocatalysts for methanol oxidation reaction

Spinel Nickel–Cobalt Oxide Nanorods Supported on Ti3C2Tx-MXene Nanosheets As Electrocatalysts for the Methanol Oxidation Reaction Via a CO-Free Pathway