Abstract:In this work, high energy synchrotron X-ray diffraction was used during tensile testing of an as-cast eutectic AlCoCrFeNi2.1 high entropy alloy. Aside, from determining for the first time the volume fractions of existing phases, we further detail their role on the alloy deformation behavior. The two major phases, a soft disordered FCC and a hard ordered B2 BCC, were observed to exhibit a stress partitioning effect which can be used to modulate the mechanical response of the material based on the relative volume fraction of each phase. Dislo-cation density analysis revealed that the soft FCC phase had a significantly higher dislocation density right after the onset of plastic deformation. This is attributed to the existence of strain gradients across the lamellar structure, where the hard B2 BCC prevents free deformation of the FCC phase. Nonetheless, despite the increase of the dislocation density in the soft FCC phase, calculations of the strengthening effects induced by generation of dislocations are more significant in the hard B2 BCC phases, as this phase is primarily responsible for the strength increase in the alloy. Besides, the evolutions in dislocation density of the soft FCC and hard B2 BCC phases during tensile deformation obtained from synchrotron X-ray diffraction data are consistent with the evolution of KAM determined by EBSD characterization. Also, lattice strain analysis across two principal directions (parallel and perpendicular to the loading axis) reveals that for these specific orientations there is a preferential deformation of the hard FCC planes which can be related to the deformation response of specific lattice planes at distinct ori-entations, as well as to the phase partitioning stress behavior.

Surface degradation mechanisms in a eutectic high entropy alloy at microstructural length-scales and correlation with phase-specific work function

Phase Structure, Microstructure, Corrosion, and Wear Resistance of Al0.8CrFeCoNiCu0.5 High-Entropy Alloy

Surface degradation mechanisms in precipitation-hardened high-entropy alloys

Microstructural Analysis, Corrosion Resistance, and Wear Performance Study of Al0.8FeCoNiCrCu0.5Si0.2 0.8 FeCoNiCrCu 0.5 Si 0.2 High-Entropy Alloy

Microstructural origins of high strength and high ductility in an AlCoCrFeNi2.1 eutectic high-entropy alloy

Deformation Behavior and Strengthening Effects of an Eutectic AlCoCrFeNi2.1 High Entropy Alloy Probed by In-Situ Synchrotron X-ray Diffraction and Post-Mortem EBSD

Phase-Specific Damage Tolerance of a Eutectic High Entropy Alloy

Accelerated Corrosion of High Entropy Alloys under Tensile Stress

Corrosion behavior and mechanism of dual phase Fe1.125Ni1.06CrAl high entropy alloy

Microstructure, Mechanical and Corrosion Properties of Al–Co–Cr–Ni Near-Eutectic Medium Entropy Alloys

Microstructure and mechanical properties of a high entropy alloy with a eutectic composition (AlCoCrFeNi2.1) synthesized by mechanical alloying and spark plasma sintering

Microstructural evolution, mechanical and corrosion behavior of an Al7.5Co20.5Fe24Ni24Cr24 high‐entropy alloy

Comparative Study of Mechanical and Corrosion Behaviors of Cost-Effective AlCrFeNi High Entropy Alloys

Influence of ordered L12 precipitation on strain-rate dependent mechanical behavior in a eutectic high entropy alloy

Microstructure and Corrosion Behavior of AlCoCrFeNiSi0.1 High-Entropy Alloy

Microstructural Features, Corrosion and Wear Behavior of the AlCrFeCoNiCu High-Entropy Alloy, Electrodeposited Coatings, and Subsequent Heat Treatment

Evaluation of Tribological and Electrochemical Properties of Multiphase CoCuFeNiNb High Entropy Alloy

Influence of Cu and Co addition on metallurgical and wear characteristics of AlCrFeNi high entropy alloy

High-strength AlCoCrFeNi2.1 eutectic high entropy alloy with ultrafine lamella structure via additive manufacturing

Microstructure and Corrosion Properties of Cr41CoFeNi Eutectic High-Entropy Alloy in Sulfuric Acid Solution

Physicomechanical and design characteristics of surface high-entropy alloys