Abstract:The paper evaluates the results of tests performed using mid- and high-level blends of the low-carbon alcohols, methanol and ethanol, in admixture with gasoline, conducted in a variety of test engines to investigate octane response, efficiency and exhaust emissions, including those for particulate matter. In addition, pure alcohols are tested in two of the engines, to show the maximum response that can be expected in terms of knock limit and efficiency as a result of the beneficial properties of the two alcohols investigated. All of the test work has been conducted with blending of the alcohols and gasoline taking place outside the combustion system, that is, the two components are mixed homogeneously before introduction to the fuel system, and so the results represent what would happen if the alcohols were introduced into the fuel pool through a conventional single-fuel-pump (dispenser) approach. While much has been written on the effect of blending the light alcohols with gasoline in this way, the results present significant new findings with regard to the effect of the enthalpy of vaporization of the alcohols in terms of particulate exhaust emissions. Also, in one of the tests, two mid-level blends are tested in a highly downsized prototype engine – these blends being matched for stoichiometry, enthalpy of vaporization and volumetric energy content. The consequences of this are discussed and the results show that this approach to blend formulation creates fuels which behave in the same manner in a given combustion system; the reasons for this are discussed. One set of tests using pure methanol alternately with cooled exhaust gas recirculation and with excess air shows a significant increase in thermal efficiency that can be expected as the blend level is increased. The effect on nitrous oxide emissions is shown to be similarly beneficial, this being primarily a result of the enthalpy of vaporization of the alcohol cooling the charge coupled with the lower adiabatic flame temperature of the alcohol. Whereas it is normally a beneficial characteristic in spark-ignition combustion systems, one disadvantage of a high value of enthalpy of vaporization is shown in another series of tests in that, in admixture with gasoline, it is a driver on flash boiling of the hydrocarbon component in the blend in direct injection combustion systems. In turn, this causes the particulate emissions of the engine to increase quite markedly over those of ethanol–gasoline blends at the same stoichiometry. The paper shows for the first time the dichotomy of the potential efficiency improvement with the challenge of particulate control. This effect poses a challenge for the future introduction and use of such high blend rate fuels in engines without particulate filters. Although it must be stated that the overall particulate emissions of the methanol–gasoline blend are lower than for gasoline, the effect is only present at extremely low load, and that there is a likelihood that particulate filters will be adopted in production vehicle anyway, nullifying this issue.

Performance Analysis of an IC Engine Using Methanol, Ethanol, and Its Blend with Gasoline and Diesel as a Fuel

Engine Performance and Emissions of A Compression Ignition Engine Operating on the Diesel-Methanol Blends

Alcohol fuels for spark-ignition engines: Performance, efficiency and emission effects at mid to high blend rates for binary mixtures and pure components

Investigations on the noise and vibration characteristics of SI engine powered with single and dual alcohol blends - performance, combustion, and emission studies

Influence of Higher Alcohol Additives in Methanol–Gasoline Blends on the Performance and Emissions of an Unmodified Automotive SI Engine: A Review

A critical review: Application of methanol as a fuel for internal combustion engines and effects of blending methanol with diesel/biodiesel/ethanol on performance, emission, and combustion characteristics of engines

Combustion Performance of Bio-Ethanol at Various Blend Ratios in A Gasoline Direct Injection Engine

EXPERIMENTAL INVESTIGATION OF THE PERFORMANCE AND EMISSION CHARACTERISTICS OF METHANOL-ETHANOLGASOLINE BLENDING WITH ISO-BUTANOL ADDITIVE ON THE SPARK-IGNITION ENGINE

Alcohol fuels in SI engines: a comprehensive state-of-the-art review on combustion, performance, and environmental impacts

Experimental study on the performance of a high compression ratio SI engine using alcohol/ammonia fuel

Comparative study on combustion and emission characteristics of methanol/hydrogen, ethanol/hydrogen and methane/hydrogen blends in high compression ratio SI engine

A comparative assessment of performance and emission characteristics of a DI diesel engine fuelled with ternary blends of two higher alcohols with lemongrass oil biodiesel and diesel fuel

Evaluation of performance and emissions characteristics of methanol blend (gasohol) in a naturally aspirated spark ignition engine

A comprehensive review on combustion, performance and emission aspects of higher alcohols and its additive effect on the diesel engine

Analyzing the combustion and emissions of a DI diesel engine powered by primary alcohol (methanol, ethanol, n-butanol)/diesel blend with aluminum nano-additives

Experimental and numerical study on a SI engine fueled with gasohol and dissociated methanol gas blends at lean conditions

Comparative Assessment of Ethanol and Methanol–Ethanol Blends with Gasoline in SI Engine for Sustainable Development

Performance of SI Engine to Improve the Combustion Characteristics by Using Methanol Blended Petrol

Performance, Combustion, and Emission Evaluation of Ethanol-Gasoline Blends Ignited by Diesel in Dual-Fuel Intelligent Charge Compression Ignition (ICCI) Engine

Effect of the addition of 1-pentanol on engine performance and emission characteristics of diesel and biodiesel fuelled single cylinder diesel engine

Energy and exergy analysis of a SI engine fueled with anisole and isobutyl acetate with super-premium gasoline