Abstract:This study employed a viscoplastic finite element model and re-meshing technique to investigate the thermomechanical response of 7055 aluminum alloy during friction stir welding (FSW). The stirring pin rotates at 800-1200 rpm and moves at 80-120 mm/min (i.e., welding speed) during the FSW process. The temperature field and viscoplastic flow were mathematically modeled based on a computational solid mechanics method and predicted by a three-dimensional coupled thermomechanical numerical simulation. To validate the simulation results, real-time temperature measurements at the welded joint were acquired via thermocouples embedded in the plate prior to the welding process. Additionally, optical microscopy and electron backscatter diffraction techniques were used to examine the metallographic structure and grain orientation of the welds, respectively. The results revealed a temperature difference of 5-10 celcius between the advancing and retreating sides of the plate. The material on the advancing side was extruded upward in a circular motion and eventually reached the surface. Meanwhile, the material on the retreating side moved half a revolution around the pin and remained at the original depth of the plate. Complete dynamic recrystallization occurred in the weld nugget, resulting in the formation of fine equiaxed grains with random orientation. In the thermomechanically affected zone, the proximity to the weld nugget was associated with an increased proportion of high-angle grain boundaries and recrystallized structures. Simultaneously, the intensity of the deformation texture decreased, while the recrystallized texture showed an initial strengthening followed by a subsequent weakening. This comprehensive investigation contributes to a deeper understanding of the thermomechanical behavior and metallographic characterization of 7055 aluminum alloy during the FSW process.

Joining Performance and Microstructure of the 2024/7075 Aluminium Alloys Welded Joints by Vaporizing Foil Actuator Welding

Interfacial Microstructures and Mechanical Property of Vaporizing Foil Actuator Welding of Aluminum Alloy to Steel

Study on formability and deformation behavior of friction stir welding AA2024-7075 joint

Microstructure, microhardness and mechanical behavior of dissimilar AA7075/AA6061 alloys under friction stir welding

Impact Welding of Aluminum AA1060 and Copper T2 Sheets by Vaporizing Foil Actuator: Microstructure, Mechanical Properties, and Electrical Conductivity

Effect of interlayer thickness and gap distance on vaporizing foil actuator welding of 5A06 aluminium alloy and 321 stainless steel

Microstructure and mechanical properties of friction stir welded powder metallurgy AA2024 alloy

Interfacial Characteristics of Ti/Al Joint by Vaporizing Foil Actuator Welding

Microstructures and Mechanical Properties of Micro Friction Stir Welding (μfsw) of 6061-T4 Aluminum Alloy

Impact Welding of Aluminum to Copper and Stainless Steel by Vaporizing Foil Actuator: Effect of Heat Treatment Cycles on Mechanical Properties and Microstructure

Interfacial energy conversion mechanism between 3003 aluminum alloy and 321 stainless steel in vaporizing foil actuator welding process

Effect of material position and tool offset on the microstructure and mechanical properties of friction stir welded AA7075/AZ31B with ultrasonic assistance

Tailoring the Microstructure of an AA5754 Aluminum Alloy by Tuning the Combination of Heat Treatment, Friction Stir Welding, and Cold Rolling

Microstructure and mechanical properties of 6061-T6 aluminum alloy and Q235 steel via probeless friction stir extrusion joining

Microstructure and fatigue performance of friction stir welded joints of 2A12‐T4 and 7075‐T6 dissimilar aluminum alloy

Standoff-free vaporizing foil actuator welding: Process principle, experimental validation, and mechanisms analysis

Microstructure and Mechanical Properties in Friction Stir Welded 5A06 Aluminum Alloy Thick Plate

Thermomechanical Behavior and Microstructural Characteristics of 7055 Aluminum Alloy During Friction Stirring Welding

Evolution of Precipitates in a Mechanical Vibration-Assisted Metal Inert Gas Welded Joint of 6082-T6 Aluminum Alloy Made with an ER5356 Filler Wire

Microstructure and properties of friction stir welding 6061 aluminum alloy joint

Effect of Tungsten Mesh Interlayer on Microstructure and Mechanical Performance of A6061/Ti6Al4V Dissimilar Joints