Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Effect of Temperature on the Tear Fracture and Fatigue Life of Carbon-Black-Filled Rubber

The Influence of Temperature and Crack Path Deviation on the Fatigue Crack Growth of a Non-crystallizing Rubber

Coupling effect of non‐relaxing and high temperature on fatigue properties of carbon‐black filled isoprene rubber

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Relationship Between The Material Properties And Fatigue Crack-Growth Characteristics Of Natural Rubber Filled With Different Carbon Blacks

Temperature-Dependent Tearing Behavior of Rubber Materials: Characterization and Modeling

Development of Fatigue Life Model for Rubber Materials Based on Fracture Mechanics

Impact of Uniaxial Tensile Fatigue on the Evolution of Microscopic and Mesoscopic Structure of Carbon Black Filled Natural Rubber.

Experimental Investigation on Temperature Dependence of Hyperelasticity of Carbon Black Particle-Filled Rubber within Moderate Finite Deformation

Temperature effects on the lifetime reinforcement due to strain-induced crystallization in carbon black filled natural rubber under non-relaxing torsion: Comparison with non-relaxing tensile loadings

Study of the Effect of Carbon Black Filling on the Mechanical Behavior of Rubber Hyper-Elasticity

Comparative Study on the Effect of Carbon Nanotubes and Carbon Black on Fatigue Properties of Natural Rubber Composites

Temperature and Frequency Dependent Rheological Behaviour of Carbon Black Filled Natural Rubber

Effect of Formula Factors on High-temperature Tear Strength of Fluororubber

Effect of thermo-oxidative aging on the Payne effect and hysteresis loss of carbon-black filled rubber vulcanizates

Fatigue behavior of polyester/ rubber composites and rayon/rubber composites under periodic loading

Study on the aging of three typical rubber materials under high- and low-temperature cyclic environment

EXPERIMENTAL STUDY ON THE TEMPERATURE DEPENDENCE OF HYPERELASTIC BEHAVIOR OF TIRE RUBBERS UNDER MODERATE FINITE DEFORMATION (vol 84, pg 215, 2011)

Experimental Studies on Fatigue Damage of Polyester Reinforced Rubber

EXPERIMENTAL STUDY ON THE TEMPERATURE DEPENDENCE OF HYPERELASTIC BEHAVIOR OF TIRE RUBBERS UNDER MODERATE FINITE DEFORMATION

Investigation of the Carbon‐Black Network in Natural Rubber Under Cyclic Deformation