Abstract:The aluminum fly ash metal matrix composites (MMCs) find important applications in automobile and aerospace where high strength and modulus is important. The fly ash by product of coal burning is drawing lot of attention as reinforcement for MMCs due to its low cost and reduction in environmental pollution. The ash particles, generally being hollow in nature, display lower densities while oxides present as constituents make them possess high modulus and strength thereby enhancing specific strength and stiffness along with lower densities compared to many metal based systems. The uses of MMCs are impeded in critical applications due to its low fracture toughness as compare to metals. LEFM (Linear Elastic Fracture Mechanics) has been used by researchers to characterize the plane strain fracture toughness using various specimen geometries and notches. However there were very few studies using EPFM (Elastic Plastic Fracture Toughness) are reported in open literature. In the present paper the influences of weight fraction of fly ash reinforcement on hardness, tensile strength and fracture toughness have been evaluated. Hardness of aluminium fly ash metal matrix composites increases with the addition of fly ash particulate reinforcement. However the tensile strength and fracture toughness KIC and JIC of the aluminum fly ash composite decreases that of base alloy. The fracture toughness of AA2024 varied between 17-18 MPa√�� as compared to 21 MPa√�� for remelted base alloy AA2024, which is consistent with the reported data. The JIC fracture toughness of AA2024 fly ash composites varied between 6-15 KJ/m² as compared to 25 KJ/m² for the re melted base alloy AA2024. The load and COD plot shows hysteresis loop in loading and unloading compliance curve. This hysteresis loop is indicative of crack closure due to fly ash particles. The reason for crack closure may be surface roughness resulting from reinforcement particles in the composites. The fracture behavior and micro-mechanism of failure in base alloy and composites have been observed under SEM and optical microscopy.

Comparisons of Experimental Fracture Toughness Testing Methods of Al6061–Graphite Particulate Composites

Fracture Toughness of AA2024 Aluminum Fly Ash Metal Matrix Composites

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Evaluation of Mechanical and Thermal Properties of Aluminium-7475 Reinforced with Graphite and Fly ash

Fracture analysis of AA6061-graphite composite for the application of helicopter rotor blade

Mechanical Behaviour and Fractured Surface Analysis of Bauxite Residue and Graphite Reinforced Aluminium Hybrid Composites

Evaluation of mechanical and thermal properties of Al 7475–CSA–graphite hybrid metal matrix composites

Properties of aluminum graphite composite prepared by stir casting

Mechanical and wear analysis of AA6061-T6-SiC-TiC-graphite metal matrix composite

Performance analysis and mechanical behavior of aluminum metal matrix composite

Investigating the Effect of Particle Sizes of SiC and Graphite on Strengthening of Aluminium Metal Matrix Composites

Development and wear behavior investigation on aluminum-7075/B4C/fly ash metal matrix composites

Experimental Investigation on Metal Matrix Nanocomposite: Aluminium Alloy 6061 and 7075 with SiC and Fly Ash

Mechanical Properties of Aluminum-4043/Nickel-coated Silicon Carbide Composites Produced via Stir Casting

Investigation of Microstructures and Mechanical Properties of Al2024/6061/7075-Graphene Composites

Investigation of Mechanical Properties of Aluminium 6061-Silicon Carbide, Boron Carbide Metal Matrix Composite

Experimental Investigation on Mechanical Properties of AA2195-based MMCs for Space Applications

Microstructure and mechanical properties of graphite fiber-reinforced high-purity aluminum matrix composite

Investigation On Tensile Properties Of Aluminum 7075 - Silica Particles -Boron Fiber- Reinforced Hybrid Metal Matrix Composites

Investigation Of Microstructural Evolution And Mechanical Properties Of Surface Graphitized Al-1100 Alloy

An appraisal of characteristic mechanical properties and microstructure of friction stir welding for Aluminium 6061 alloy – Silicon Carbide (SiCp) metal matrix composite