Abstract:Abstract. Accurate knowledge of the input torque in wind turbine gearboxes is key to improving their reliability. Traditionally, rotor torque is measured using strain gauges bonded to the shaft. Transferring the resulting signal from the rotating shaft to a stationary data acquisition system while powering the sensing devices is complex and costly. The magnitude of the torques involved in wind turbine gearboxes and the high stiffness of the input shaft pose additional difficulties. This paper presents a new alternative method to measure the input torque in wind turbine gearboxes based on deformation measurements of the static first stage ring gear. We have measured deformation using fiber optic strain sensors based on fiber Bragg gratings because of their advantages compared to conventional electrical strain gauges. The present study was conducted on a Siemens Gamesa Renewable Energy gearbox with a rated power of 6MW, in which a total of 54 fiber optic strain sensors were installed on the outer surface of the first stage ring gear. The gear mesh forces between the planets and the ring gear cause measurable deformations on the outer surface of the stationary ring gear. The measured strains exhibit a dynamic behavior. The strain values change depending on the relative position of the strain sensors to the planet gears, the instantaneous variations of the input torque, and the way load is shared between planets. A satisfactory correlation has been found between the strain signals measured on the static ring gear and torque. Two signal processing strategies are presented in this paper. The first procedure is based on the peak-to-peak strain values computed for the gear mesh events, and therefore, torque can only be estimated when a gear mesh event is detected. The second signal processing procedure combines the strain signals from different sensors using a Coleman coordinate transformation and tracks the magnitude of the fifth harmonic component. With this second procedure, it is possible to estimate torque whenever strain data of all sensors is available, leading to an improved frequency resolution up to the sampling frequency used to acquire strain data. The method presented in this paper could make measuring gearbox torque more cost-effective, which would facilitate its adoption in serial wind turbines and enable novel data-driven control strategies, as well as a more accurate assessment of the consumed fatigue life of the gearboxes throughout their operation.

Etched and Nanocoated Single-Mode Multimode Single-Mode (SMS) Fibers for Detection of Wind Turbine Gearbox Oil Degradation

Micro/Nanofibre Optical Sensors: Challenges and Prospects

Modulation of the Dual Resonant Peaks of a Long-Period Fiber Grating Towards Highly Sensitive Sensing by Means of Polymeric Nanocoatings for Biosensing Applications

Refractive Index Sensors Based on Ag-metalized Nanolayer in Microstructured Optical Fibers

High-power Continuous-Wave Optical Waveguiding in a Silica Micro/nanofibre.

Reel-to-Reel Fabrication of In-Fiber Low-Loss and High-Temperature Stable Rayleigh Scattering Centers for Distributed Sensing

Optical nanofiber temperature monitoring via double heterodyne detection

Optical nanofibers and spectroscopy

Sub-femtogram Sensing by Engineering Evanescent Field on a Single Serially Grafted Waveguide

Design mode filtering interferometer using etched double clad fiber

Monitoring the Oil of Wind-Turbine Gearboxes: Main Degradation Indicators and Detection Methods

Lossy mode resonance sensors based on lateral light incidence in nanocoated planar waveguides

Input Torque Measurements for Wind Turbine Gearboxes Using Fiber Optical Strain Sensors

Optical Properties of a Tapered Optical Fiber Coated with Alkanes Doped with Fe3O4 Nanoparticles

Enhanced Evanescent Field Spectroscopy at Waveguide Surfaces using High Index Nano and Near-Nano Layers

Nano Application of Oil Concentration Detection Using Double-Tooth Ring Plasma Sensing

Near-Field Characterization of Optical Micro/Nanofibres

Design of composite optical nanofibers for new all-solid state Raman wavelength converters

A Transflective Nano-Wire Grid Polarizer Based Fiber-Optic Sensor

Turn Around Point Long Period Fiber Gratings With Coupling to Asymmetric Cladding Modes Fabricated by a Femtosecond Laser and Coated With Titanium Dioxide

Low-Cost Online Monitoring System for the Etching Process in Fiber Optic Sensors by Computer Vision