Abstract:As a processing technique to change the organization and properties of materials, heat treatment was widely used to strengthen metallic materials. This study examines the impact of varying cooling rates and heat treatment durations on the mechanical properties and microstructure of AlSi10Mg alloys produced through Selective laser melting (SLM). The heat treatment process was Solution Heat Treatment (SHT, 525 °C), and the heat treatment time includes 1 h, 2 h, and 3 h. Cooling methods consist of Refrigerant Cooling (RC), Water Cooling (WC), Air Cooling (AC), Oil Cooling (OC), and Furnace Cooling (FC). As the cooling rate decreases and the heat treatment time increases, the size of the formed Si phase particles varies from small to large, and the distribution deviates from inhomogeneous to homogeneous. In addition, the number of precipitated particles increases and then decreases. To investigate the impact of cooling rates and heat treatment time on the mechanical properties of AlSi10Mg alloys, quasi-static tensile and compression tests were performed. On the other hand, the tensile strength of the heat-treatment samples decreases while the ductility increases, and the Vickers hardness of the samples also decreases with decreasing cooling rate and increasing heat treatment time. The results of the study showed that the cooling rate and heat treatment time of the material had a greater effect on its tensile properties than on its compressive properties. The samples treated at 525 °C - 2 h - AC exhibited the highest tensile and compressive properties. Finally, the analysis of the strengthening mechanism of AlSi10Mg alloys through the presence of Si phase particles of varying sizes was conducted using transmission electron microscopy.

Effect of Melt Treatment with Water Vapor on Thermal Expansion of Alloy Al – 20–40% Si

The Effect of Solution Treatment on the Si Particles’ Morphology Evolution and the Thermal Conductivity and Tensile Properties of Sb-Modified Al-8Si-0.6Mg Alloys

Influence of Heat Treatment on Microstructure and Thermo-Physical Properties of Al-50wt%Si Alloy Fabricated by Selective Laser Melting

Effect of solution heat treatment on the internal architecture and compressive strength of an AlMg4.7Si8 alloy

Effect of cooling rates and heat treatment time on Si phase of AlSi10Mg alloy manufactured by selective laser melting: Microstructure evolution and strengthening mechanism

The Effect of Heat Treatments on the Microstructural Evolution of Twin-Roll-Cast Al-Fe-Si Alloys

Effect of the Melt Temperature Treatment on the Structure and Mechanical Property of AI-19%Si Alloy

Effects of melt thermal treatment on hypoeutectic Al–Si alloys

Influence of Thermal Rate Treatment and Low Temperature Pouring on Microstructure and Tensile Properties of AlSi7Mg Alloy

Investigation of the influences of heat treatment on the microstructures and thermal properties of Al-20Si alloy fabricated by powder extrusion

Effect of Silicon Addition and Thermal History on the Thermal Expansion Behavior of Sic/Al Composites

Experiment and numerical simulation of aluminum silicon alloy corrosive treatment in the water vapor generation autoclaves

EFFECTS OF HEAT TREATMENT ON THE THERMAL EXPANSION BEHAVIOR OF SiC WHISKER REINFORCED ALUMINUM COMPOSITE

Microstructure and Performance of Al-Si Alloy with High Si Content by High Temperature Diffusion Treatment

Achieving High Thermal Conductivity of Al–50Si Alloy Through Heat Treatment and Its Microstructural Evolution

Experimental and Statistical Analysis of the Effect of Heat Treatment on Surface Roughness and Mechanical Properties of Thin-Walled Samples Obtained by Selective Laser Melting from the Material AlSi10Mg

The evolution on the microstructure and thermal expansion behavior of Al–50Si alloy with different P contents

Effect of Heat Treatment on the Microstructure and Mechanical Properties of TiAl Alloys

Sub-micrometre holotomographic characterisation of the effects of solution heat treatment on an AlMg7.3Si3.5 alloy

Effect of extrusion temperatures on the microstructures, mechanical properties and thermal properties of PM Al-20Si alloy

Effect of thermal treatments on the surface electrical conductivity of AlSi7Mg produced by laser powder bed fusion