Abstract:A long‐cycle‐life solid‐state Li–CO2 battery operating at elevated temperatures by constructing a stable and high ionic conductive molten salts interface (MSI) is reported. The MSI can effectively improve the interface contact and suppress interface reactions between the Li‐anode and LAGP‐electrolyte even at 150 °C, thus the assembled solid‐state Li–CO2 battery shows outstanding cycle stability over 980 cycles. High‐energy rechargeable lithium‐ion batteries, especially solid‐state lithium metal batteries, are increasingly required to operate at elevated temperatures in addition to pursuing operation at low temperatures. However, the notorious chemical and electrochemical reactions at the interface between the Li‐anode and solid state electrolyte (SSE) make these batteries lose almost all of their capacity and power at elevated temperatures. Here, a safe and long‐cycle‐life solid‐state Li–CO2 battery operating at elevated temperatures by constructing a stable and high ionic conductive molten salts interface (MSI) is reported. The MSI can effectively improve the interface contact and suppress interface reactions and the thermal runaway between Li‐anode and Li1.5Al0.5Ge1.5P3O12 (LAGP)‐electrolyte even at high temperatures, thus enabling an ultra‐low interface impedance (≈15 Ω) and discharge/charge overpotential (≈15 mV) for high temperature symmetric battery. In addition, the MSI‐coated LAGP‐electrolyte shows an ultra‐flat and continuous surface that enables a homogeneous Li tripping/plating during cycles. As a result, the Li symmetric battery shows superior cycling stability over 600 h at 0.1 mA cm−2 at 150 °C. The assembled solid‐state Li–CO2 battery using Ru catalysts shows outstanding cycle stability over 980 cycles at 150 °C, with a capacity limitation of 500 mAhg–1 at 500 mA g−1.

Improving cyclability of Li metal batteries at elevated temperatures and its origin revealed by cryo-electron microscopy

A Lithium Metal Anode Surviving Battery Cycling above 200 °C.

Cycling a Lithium Metal Anode at 90 °C in a Liquid Electrolyte.

Highly Thermostable Interphase Enables Boosting High‐Temperature Lifespan for Metallic Lithium Batteries

High Voltage Stable Li Metal Batteries Enabled by Ether-Based Highly Concentrated Electrolytes at Elevated Temperatures

High‐Performance Lithium Solid‐State Batteries Operating at Elevated Temperature

Lithium Metal Anodes: A Lithium Metal Anode Surviving Battery Cycling Above 200 °C (Adv. Mater. 29/2020)

Efficient Low-Temperature Cycling of Lithium Metal Anodes by Tailoring the Solid-Electrolyte Interphase

Stable High‐Temperature Lithium‐Metal Batteries Enabled by Strong Multiple Ion–Dipole Interactions

Deciphering Interphase Instability of Lithium Metal Batteries with Localized High-Concentration Electrolytes at Elevated Temperatures

A High‐Energy Long‐Cycling Solid‐State Lithium‐Metal Battery Operating at High Temperatures

Thermal behavior of Li electrode in all-solid-state batteries and improved performance by temperature modulation

Tailoring electrolyte solvation for Li metal batteries cycled at ultra-low temperature

Temperature-dependent interphase formation and Li+ transport in lithium metal batteries

Reinforced interface endows the lithium anode with stable cycle at high-temperature of 80 o C

High‐Voltage Li‐Ion Full‐Cells with Ultralong Term Cycle Life at Elevated Temperature

Reinforced interface endows the lithium anode with stable cycle at high-temperature of 80 °C

Reinforced interface endows the lithium anode with stable cycle at high-temperature of 80 degrees C

Enhanced low-temperature resistance of lithium-ion batteries based on methyl propionate-fluorinated ethylene carbonate electrolyte

Low-temperature and high-rate-charging lithium metal batteries enabled by an electrochemically active monolayer-regulated interface