Abstract:The texture of Mg alloy dendrites is quite different from that of fcc or bee metals because of the influence of hcp crystal lattice on the dendrite morphology evolutions during solidification. Although the simulations of dendrite morphologies for fee or bcc metals by cellular automaton (CA) methods have been widely reported, CA simulations of magnesium alloys with hcp crystal lattice have just appeared in recent years. When performing the simulation of Alg alloy dendrites with a CA method on a square mesh, the artificial anisotropy of growth kinetics introduced by the square mesh makes it hard to reflect the texture of Mg alloy dendrites, which shows the six-fold symmetry instead of four-fold symmetry of bcc or fcc metal dendrites.In the present paper, a two dimensional CA model has been developed for simulating the dendrite morphology evolution of cast Mg alloys. The model employs two sets of meshes to perform the numerical simulation, where a hexagonal mesh is used to perform CA calculation to reflect the texture of Mg alloy dendrites, and an orthogonal mesh is used to solve the mass transportation equation. The two sets of meshes are coupled by an interpolation method. By employing the two-set mesh method, the texture of Mg alloy dendrites is well reflected and the undesired artificial growth kinetics introduced by square mesh is avoided. In the model, the growth kinetics of dendrite tips was determined by the difference between local equilibrium and local actual compositions obtained by solving the solute transport equation. With this calculation method for growth kinetics, the solid fraction of interface CA cell can be obtained directly from the solute field, which decreases the computational cost greatly. The model was applied to simulate the single dendrite evolution and columnar dendrite growth of AZ91D Mg alloy, as well as multi-dendrite growth and grain size of Mg-10Gd-2Y-0.5Zr (mass fraction, %) alloy step-shaped castings. To validate the current model, permanent mold sample castings of AZ91D Mg alloy and step-shaped castings of Mg-10Gd-2Y-0.5Zr alloy were produced. Optical metallographic examinations were performed on specimens of these two Mg alloys, and grain sizes were measured on solution treated specimens of Mg-10Gd-2Y-0.5Zr alloy. The simulated and experimental results were compared.

Numerical Simulation and Experimental Validation of Nondendritic Structure Formation in Magnesium Alloy Under Oscillation and Ultrasonic Vibration

Dendritic Growth in Mg-Based Alloys: Phase-Field Simulations and Experimental Verification by X-ray Synchrotron Tomography

Numerical simulation of dendritic morphology of magnesium alloys using phase field method

Numerical simulation of dendritic growth of magnesium alloy with convection

RESEARCH PROGRESS ON 3D DENDRITE MORPHOLOGY AND ORIENTATION SELECTION DURING THE SOLIDIFICATION OF Mg ALLOYS: 3D EXPERIMENTAL CHARACTERIZATION AND PHASE FIELD MODELING

Dendritic morphology of α-Mg during the solidification of Mg-based alloys: 3D experimental characterization by X-ray synchrotron tomography and phase-field simulations

A Three-Dimensional Cellular Automaton Model for Simulation of Dendritic Growth of Magnesium Alloy

Modeling of equiaxed and columnar dendritic growth of magnesium alloy

Modeling and Simulation of Microstructure Evolution of Cast Mg Alloy

Phase-field Simulations of Dendrite Morphologies and Selected Evolution of Primary Α-Mg Phases During the Solidification of Mg-rich Mg–Al-based Alloys

Two- and Three- Dimensional Studies of Dendritic Morphology in Magnesium Alloy by Means of Synchrotron X-Ray Microtomography and Cellular Automaton Modelling

Physical field of dual-frequency ultrasonic vibration and its effect on solidification behavior of MgZnY alloy

Mechanism Of The Growth Pattern Formation And Three-Dimensional Morphological Transition Of Hcp Magnesium Alloy Dendrite

Microstructure Simulation of Magnesium Alloy

Dendrite Morphology And Growth Orientation Of Magnesium Alloys: Simulation By Phase-Field And 3-D Characterization By Synchrotron X-Ray Tomography

Dendrite Growth Modelling of Cast Magnesium Alloy

Numerical Modelling Of Microstructure Evolution And Dendrite Growth In Alloy Solidification Process

Microstructures simulation of magnesium-based alloys during solidification by phase-field method

Phase-field modeling of dendritic growth of magnesium alloys with a parallel-adaptive mesh refinement algorithm

Phase field simulation on microstructure evolution in solidification and aging process of squeeze cast magnesium alloy

Modeling and Simulation of Microstructure Evolution of Cast Magnesium Alloys Using Ca Method Based on Two Sets of Mesh