Abstract:In light-duty direct-injection (DI) diesel engines, combustion chamber geometry influences the complex interactions between swirl and squish flows, spray-wall interactions, as well as late-cycle mixing. Because of these interactions, piston bowl geometry significantly affects fuel efficiency and emissions behavior. However, due to lack of reliable in-cylinder measurements, the mechanisms responsible for piston-induced changes in engine behavior are not well understood. Non-intrusive, in situ optical measurement techniques are necessary to provide a deeper understanding of the piston geometry effect on in-cylinder processes and to assist in the development of predictive engine simulation models. This study compares two substantially different piston bowls with geometries representative of existing technology: a conventional re-entrant bowl and a stepped-lip bowl. Both pistons are tested in a single-cylinder optical diesel engine under identical boundary conditions. Utilizing high-speed soot natural luminosity (NL) imaging, 20 kHz time-resolved combustion image velocimetry (CIV) technique is developed to quantify the macro-scale motions of soot clouds during the mixing-controlled portion of combustion. Under a part-load conventional combustion regime, CIV-resolved swirl ratio and the tumble-plane projection of velocity fields confirm that the injection-induced redistribution of angular momentum, rather than squish/reverse squish flow, is a dominant source for swirl amplification between two piston geometries. A strong connection has been found between the CIV-resolved combusting flow structure and its succeeding enhanced late-stage burn rate. With SOImain shortly after TDC, combustion in stepped-lip piston exhibits shorter late-burn duration (CA50-CA90) and faster burn rate compared to re-entrant piston. In the same boundary condition, a unique combusting flow structure is observed with CIV in the stepped-lip piston: a long-lasting flow structure with opposing radial velocity directions between the squish region and stepped-lip region. Interestingly, this flow structure is never optically observed with the re-entrant piston. The best hypothesis is that there exists a long-lasting vertical toroidal vortex on the shoulder of stepped-lip piston crown near CA50. A phenomenological model is proposed to provide a partial, but valuable picture of late-stage combusting flow structure which is a key to understand how piston bowl geometry can influence thermal efficiency for swirl-supported diesel engines.

Impact of Piston Geometry on Diesel Engine Performance, Emissions and Combustion

Effect of Bowl-in-Piston Chamber on the Combustion Process in a Stoichiometric Natural-Gas Spark-Ignition Engine

Experimental study on the effect of piston bowl geometry on the combustion performance and pollutant emissions of methane-diesel common rail dual-fuel engine

Influence of piston bowl geometry on combustion and emission characteristics

An experimental investigation on the influence of piston bowl geometry on RCCI performance and emissions in a heavy-duty engine

Effect of piston bowl geometry and spray angle on engine performance and emissions in HCCI engine using multi‐stage injection strategy

Effect of a novel piston geometry on the combustion process of a light-duty compression ignition engine: An optical analysis

Effects of Piston Bowl Geometry on Combustion and Emissions of a Four-Stroke Heavy-Duty Diesel Marine Engine

Split-Spray Piston Geometry Optimized for HSDI Diesel Engine Combustion

Piston Crown Profile Modifications for Various Combustion Mode Strategies of Modified GDI Engine towards NOx and PM Reduction

A Study of Piston Geometry Effects on Late-Stage Combustion in a Light-Duty Optical Diesel Engine Using Combustion Image Velocimetry

Numerical Investigations of Injection Timing Effects on a GDI Engine Performance: Part B, In-Cylinder Emission Formation and Oxidation Process

Numerical Investigation of the Effect of Injection Timing on the In-Cylinder Activity of a Gasoline Direct Injection Engine

Effect of Piston Profile on Piston Motion and Liner Bore Polishing

Effects of Piston Bowl Geometries On Diesel and Gasoline Dual-Fuel Combustion under Low Load Conditions

Experimental and numerical investigation of an innovative complex piston with enhanced free spray length for the heavy-duty engine applications

Effect of Compression Ratio and Piston Geometry on RCCI Load Limits and Efficiency

CFD study and experimental investigation of piston geometry induced in-cylinder charge motion on LPG fuelled lean burn spark ignition engine

Computational analysis of piston shape effects on in-cylinder gas flow, fuel-charge mixing, and combustion characteristics in a two-stroke rod-less spark ignition opposed-pistons engine

A Piston Geometry and Nozzle Spray Angle Investigation in a DI Diesel Engine by Quantifying the Air-Fuel Mixture