Abstract:We conducted a study to investigate the impact of the laser direct metal deposition (LMD) process on the microstructure, mechanical properties, temperature fields, and stress fields of 24CrNiMo steel in order to determine the optimal process parameters. The optimal parameters were determined to be a laser power of 1400 W, scanning speed of 7 mm/s, and powder feed rate of 8 g/min. When these optimal parameters were used, the formed specimens exhibited a high densely of up to 97.5 %. The microstructure of the specimens formed different parameters primarily consisted of bainite, martensite and ferrite. The specimens formed under various process conditions demonstrated good toughness, with a maximum tensile strength of 1131±20 MPa and an elongation of 16±1.8 %. Additionally, there was little difference in wear resistance and wear morphology among the specimens formed under different processes. The predominant wear mechanisms include abrasive wear, adhesive wearand oxidative wear. Increasing laser power and decreasing scanning speed resulted in a gradual increase in the temperature gradient gradually, leading to higher residual stresses in the formed specimens. Longitudinal stresses concentrated on both sides of the deposited layer, while the transverse stresses concentrated on one side of the deposited layer. The simulation results of the temperature field and stress field were consistent with the experimental results, with errors within the range of 10 %–20 %. This study demonstrated that the simulated models of temperature and stress fields effectively captured the fundamental phenomena in the LMD process, providing valuable tools for predicting and optimizing temperature distribution and stress in the LMD process. These findings contribute to the understanding and enhancement of the LMD process for 24CrNiMo steel, making it applicable for various applications requiring superior microstructure and mechanical properties.

Microstructural Evolution and Properties of 24CrNiMoY Alloy Steel Fabricated by Selective Laser Melting

Achieving Excellent Strength and Ductility of 24crnimoy Alloy Steel Fabricated by High Power Selective Laser Melting Technology

Effects of process parameters on the microstructure and mechanical properties of 24CrNiMo steel fabricated by selective laser melting

Effect of Heat Treatment on Microstructure and Properties of 24CrNiMo Alloy Steel Formed by Selective Laser Melting (SLM)

Effect of Thermal Cycle on Microstructure Evolution and Mechanical Properties of Selective Laser Melted Low-Alloy Steel

Effect of Y 2 O 3 on microstructure and mechanical properties of 34CrNiMo6 steel fabricated by laser-directed energy deposition

Effect of grain boundary character on isothermal phase transformation and mechanical properties of Co-Cr-Mo alloy fabricated by selective laser melting

Morphology and Properties of CoCrMo Parts Fabricated by Selective Laser Melting

Effect of laser direct metal deposition process on the microstructure and mechanical properties and temperature and stress fields of 24CrNiMo

Influence of Cr/Mo ratio on microstructure and mechanical properties of the Ni-based superalloys fabricated by laser additive manufacturing

Heat treatment induced microstructural evolution, oxidation behavior and tribological properties of Fe-12Cr-9Ni-2Al steel (CX steel) prepared using selective laser melting

Microstructure and properties of AlCoCrFeNi 2.1 eutectic high entropy alloy manufactured by selective laser melting

Effects of laser power on the microstructural evolution of novel Ti–6Zr–5Fe alloy fabricated by selective laser melting

Optimization of laser energy density and scanning strategy on the forming quality of 24CrNiMo low alloy steel manufactured by SLM

The Effect of Annealing on Mechanical Properties of Selective Laser Melted CoCrNi Medium-Entropy Alloy

Study on phase transformation behavior and mechanical properties of equiatomic ratio NiTi alloy formed by selective laser melting

Effect of Different Heat Treatments on the Microstructural Evolution and Mechanical Properties of Ni-Cr-Si Alloy Fabricated by Laser Additive Manufacturing

Cryogenic mechanical behavior of a FeCrNi medium-entropy alloy fabricated by selected laser melting

Anisotropic Response of CoCrFeMnNi High-Entropy Alloy Fabricated by Selective Laser Melting

Significant transitions of microstructure and mechanical properties in laser additive manufacturing AlCoCrFeNi 2.1 eutectic high-entropy alloy under heat treatment

Microstructure and properties of oxide-reinforced FeCrAl matrix alloy manufactured by selective laser melting