Abstract:Journal of Reinforced Plastics and Composites, Ahead of Print. Polymer-based composites (GFRP) are increasingly used in the mechanical industry due to their cost-profitability, durability, and good mechanical properties. In the present study, a metal carbide tool was employed to manufacture polyamide (PA66-GF30%) specimen in a dry environment. The impact of variations in cutting process parameters on the responses studied is investigated using two experimental techniques. The first is the OFAT approach. For the second technique (multifactorial), the effects of input parameters on technological parameters (Ra, Fz, MRR, and Pc) are quantified aided by the ANOVA method using an experimental design based on Taguchi's L9 (3 × 3) orthogonal matrix. Based on the RSM methodology, the results were processed statistically to propose prediction models for the different outputs. In addition, a single-objective optimization study of Taguchi's and a multi-objective optimization of the operating conditions using the classification method based on CoCoSo as well as the DF Approach according to two desired objectives were carried out. The first objective of this study concerns the minimization of (Ra, Fz, and Pc), and the second one considers the minimization of (Ra, Fz, and Pc) at the same time as maximizing (MRR). Finally, the surface roughness criteria (Ra and Sa) of PA66-GF30% were evaluated to study the effect of the feed (f) on the machined surface topography. The findings are of capital importance in that they provide the required and correct information about the working conditions of composite polymers. According to "OFAT" results, feed (f) is the predominant factor influencing roughness (Ra). Temperature in the cutting zone rises with increasing cutting conditions (Vc, f and ap). Variations in cutting conditions affect the morphology of the chip produced. The roughness criteria (Ra and Sa) results clearly show that the topography of the PA66-GF30% surface changes as (f) changes. Also, optimization of all performance parameters simultaneously indicates that the DFA offers the best combination of parameters: Vc = 187.50 m × min−1, f = 0.096 mm × rev−1, and ap = 0.866 mm, leading to the minimization of (Ra) and maximization of (MRR), with respective values of 1.24 μm and 15.614 cm3 × min−1. Furthermore, the CoCoSo method favors the minimization of (Fz and Pc) with values of 20.18 N and 69.285 W, respectively.

Optimization of Drilling Parameters of GFRP with Liquid Silicone Rubber and Fine Silica Powder by Taguchi Approach

Optimization of Drilling Parameters on Delamination and Burr Formation in Drilling of Neat CFRP and Hybrid CFRP Nano-Composites

Influence of Drilling Parameters on the Delamination and Surface Roughness of Insulative-Coated Glass/Carbon-Hybrid Composite

Effect of drilling parameters on hole quality in drilling of pultruded GFRP composite material: Surface roughness, thrust force and delamination factor

Understanding the Effect of Drilling Parameters on Hole Quality of Fiber-Reinforced Polymer Structures

Optimization of drilling delamination behavior of GFRP/clay nano-composites using RSM and GRA methods

Impact Of Drilling Parameters On The Surface Roughness Of Egg Shell Filled Glass Fibre / Polyester Composites

Artificial Intelligence System Approach for Optimization of Drilling Parameters of Glass-Carbon Fiber/Polymer Composites

Drilling characteristics and properties analysis of fiber reinforced polymer composites: A comprehensive review

Investigation of the effect of AWJ drilling parameters for delamination factor and surface roughness on GFRP composite material

Impact of process parameters in drilling of glass epoxy composite with clam shell and cenosphere filler: A comparative analysis

Investigation on machining of GFRP through ANOVA, DFA, and CoCoSo method combined with Taguchi approach

Optimizing Process Parameters in Drilling of CFRP Laminates: A Combined MOORA–TOPSIS–VIKOR Approach

Effect of Drilling Force on Delamination of Abaca/Kenaf/Carbon Fiber Reinforced Hybrid Composite

Parametric optimization in drilling of sisal–glass reinforced epoxy composites using Taguchi grey relational analysis method

A Comprehensive Study on the Optimization of Drilling Performance in Hybrid Nano-Composites and Neat CFRP Composites Using Statistical and Machine Learning Approaches

Statistical modelling and assessment of surface roughness in drilling of hybrid fiber composite

Lathe Parameters Optimization for UD-GFRP Composite Part Turning with PCD Tool by Taguchi Method

Cutting parameters optimization of hybrid fiber composite during drilling

Multi-Objective Optimization of Machining Parameters for Drilling LM5/ZrO2 Composites Using Grey Relational Analysis

Investigation on carbon fiber-reinforced polymer combined with graphene nanoparticles subjected to drilling operation using response surface methodology and non-dominated sorting genetic algorithm-II