Abstract:Masonry structures often exhibit poor seismic performance during earthquakes owing to their low material strength, structural integrity, and ductility. To address the mechanism of in-plane damage and collapse of masonry walls subjected to earthquake ground motion, three full-size brick walls, one with structural columns and two without structural columns, were designed and constructed in this experimental study to quantitatively investigate the effect of structural columns on the seismic performance of masonry walls. Quasi-static tests of masonry walls subjected to cyclic lateral loading were conducted using electrohydraulic servo actuators. The in-plane damage evolution and failure mode of the masonry walls under lateral loading were investigated. A numerical model with a novel plastic damage constitutive model of masonry was established. The accuracy of this model and the calculation results were verified by comparing them with the crack development and mechanical property curves obtained from the experiments. Based on the numerical model, a parametric analysis was conducted to investigate the influence of critical factors, such as mortar strength, vertical load, and height-to-width ratio, on the seismic performance of masonry structures. The test results showed that structural columns can effectively improve the performance of masonry structures. Properly installed structural columns can improve the peak load-bearing capacity, ductility, and energy dissipation of masonry structures. The masonry damage constitutive model used in this study could simulate the damage to masonry wall specimens well and reflect the hysteretic curves of the specimens within an acceptable range of accuracy. Thus, it provides a valuable reference for physical experiments. An appropriate mortar strength and vertical compressive stress can effectively enhance the load-bearing capacity of masonry structures within a certain range. For structural column walls. Walls with mortar strengths (average compressive strength) of 12.5 MPa, 10 MPa, 7.5 MPa, and 5 MPa showed an increase in peak bearing capacity of 26.2 %, 23.9 %, 18.5 %, and 9.4 %, respectively, compared to walls with mortar strengths (average compressive strength) of 2.5 Mpa. The aspect ratio had a significant impact on the shear load-bearing capacity of the masonry walls. An increase in the aspect ratio led to a transition from shear failure to flexural failure and a subsequent decrease in shear load-bearing capacity. For masonry walls with structural columns, increasing the diameter of the longitudinal steel in the structural columns can enhance the load-bearing capacity of the masonry wall, resulting in a significant improvement in its overall performance.

Experimental study on earthquake-induced falling debris of exterior infill walls and its impact to pedestrian evacuation

Pedestrian evacuation simulation under the scenario with earthquake-induced falling debris

Seismic Performance of Reinforced Concrete Squat Walls with Embedded Cold-Formed and Thin Walled Steel Truss

An integrated simulation method for large‐scale earthquake‐induced falling debris in building groups

Simulation of Earthquake-Induced Hazards of Falling Exterior Non-Structural Components and Its Application to Emergency Shelter Design

Estimation of building damage caused by adjacent deep excavation in clay

Influence of Various Earth-Retaining Walls on the Dynamic Response Comparison Based on 3D Modeling

Experimental and Theoretical Study for a Displacement-Controlled Design Method of Embedded Cantilever Retaining Walls (Piles)

Determining Experimental Ductile Behavior of Composite Walls Considering Second-Order Effects: A Case Study for Multi-Celled CFST Walls

Numerical Investigation on Instability of Buildings Caused by Adjacent Deep Excavation

Seismic fragility and risk assessment of self-centering wall structures with traditional and sliding joint infill walls

Experimental Study of Evacuation from a 4-Storey Building

Experimental study on determinants of the evacuation performance in the super-high rise building

Effect of in-plane damage on the out-of-plane mechanical performance of infill walls with recycled concrete blocks

Collapse fragility analysis of self-centering precast concrete walls with different post-tensioning and energy dissipation designs

A parametric study in reinforced concrete frames with different infill wall materials

Pedestrian Simulation on Evacuation Behavior in Teaching Building of Primary School Emergencies and Optimized Design

Emergency fire evacuation simulation of underground commercial street

Damage evolution and failure mechanism of masonry walls under in-plane cyclic loading

Experimental Study on Failure Mechanism of Rc Walls with Different Boundary Elements under Vertical and Lateral Loads

Experimental and numerical study on seismic behavior of shear wall with cast‐in situ concrete infilled walls