Abstract:It has been reported that a novel multi-component styrene-butadienestyrene composite (SBSC) modifier composed of the SBS as the main content and additional components including ethyl-vinyl-acetate (EVA), maleic anhydride grafted with ethyl-vinyl-acetate (MAH-g-EVA), naphthenic oil, and antioxidant can be produced by melt blending. This SBSC modifier can be directly mixed with bitumen and aggregate to prepare bitumen mixture, thus thoroughly addressing inferior thermal storage stability of SBS-modified bitumen. However, it is necessary to explore the efficient utilization of the SBSC modifier due to its inadequate engineering application and poor dispersion when the SBSC modifier was added directly to the bitumen mixture. The objective of this research was to investigate the feasibility of using the SBSC modifier to obtain modified bitumen with acceptable thermal storage stability and other enhanced properties. Modified bitumens (SBSC-modified bitumens with 3, 4, 5, 6, 7 % SBSC modifier content, SBS-modified bitumen with 4.5 % SBS modifier content as the control sample) were prepared. The thermal storage stability of modified bitumen was investigated by the segregation test. Besides, the basic physical properties of modified bitumen were tested, including penetration, softening point, and ductility. The rheological properties were evaluated by temperature sweep test, multiple stress creep recovery (MSCR) test, rotational viscosity (RV) test and bending beam rheometer (BBR) test, respectively. Meanwhile, fluorescence microscopy and Fourier transform infrared (FTIR) spectrometer were also applied to characterize the microproperties of the modified bitumen. Results show that the difference in softening point of SBSC-modified bitumens with modifier contents ranging from 3 % to 7 % is less than 2.5 degrees C after 72 h of high temperature storage at 163 degrees C. The softening point and ductility of SBSC-modified bitumen increase considerably with the addition of the SBSC modifier but the decrements of penetration are not significant. Besides, with the increasing addition of the SBSC modifier, complex modulus, average percent recovery, and viscosity of modified bitumen all improve. Meanwhile, phase angle, non-recoverable creep compliance of modified bitumen decrease. The flexural creep stiffness also decreases with the increasing content of the SBS modifier. When the SBS content is the same, the SBSC-modified bitumen gets better thermal storage stability, high and low temperature properties than the SBS-modified bitumen. The microproperties show that the SBSC modifier can be uniformly dispersed in base bitumen and physically mixed with the base bitumen. The SBSC-modified bitumen obtains preferable thermal storage stability. The high and low temperature properties of the bitumen are also enhanced by the addition of the SBSC modifier. Meanwhile, the melt blending method does not restrict the role of the additional components in the SBSC modifier to improve the performance of bitumen. Based on the above findings, it can be considered that the use of SBSC modifier to prepare modified bitumen with enhanced performance is a promising practice. This research may shed light on the application of SBSC modifier to bitumen pavements.

Rapid determination of styrene-butadiene-styrene (SBS) content in modified asphalt based on Fourier transform infrared (FTIR) spectrometer and linear regression analysis

Probing the Modification Mechanism of and Customized Processing Design for SBS-modified Asphalts Mediated by Potentiometric Titration

Evaluation of Storage Stability of Styrene–butadiene–styrene Block Copolymer-Modified Asphalt Via Electrochemical Analysis

Application of asphalt rapid detection technology in National Highway G360 project

Thermal storage stability and rheological properties of multi-component styrene-butadiene-styrene composite modified bitumen

Analysis of Quantification and Mechanism of SBS Modifier in SBS-Modified Asphalt

Characterizing Asphalt Aging Behaviors and Rheological Properties Based on Spectrophotometry

Comparative Analysis of Rheological and Microscopic Performance of SBS Modified Asphalt Based on Field Aging and Laboratory Aging

Analysis on SBS Modified Asphalt Aging Characterization Based on Fourier Transform Infrared Spectroscopy

Microscopic Analysis of Aging Characteristics of SBS-Modified Asphalt Based on FTIR Technology

Study of the Properties and Modification Mechanism of SBS-Modified Asphalt by Dry Process

Application of the compatibility theory and the solubility parameter theory in SBS modification asphalt

Diffusion and reinforcement mechanism study of the effect of styrene/butadiene ratio on the high-temperature property of asphalt using molecular dynamics simulation

Data fusion of ultraviolet-visible and mid-infrared spectra for rapid performance inspection of paving asphalt binders

Using molecular dynamics and experiments to investigate the morphology and micro-structure of SBS modified asphalt binder

Non-isothermal Kinetics of Styrene—butadiene—styrene Asphalt Combustion

Evaluation and characterization of properties of crumb rubber/SBS modified asphalt

Effect of SBS structure on viscosity of SBS-modified asphalt based on molecular dynamics: Insights from shearing phase morphology, adsorption and swelling mechanisms

Aging Characteristics of SBS-Modified Asphalt under Thermo-Photo-Oxygen Coupling Conditions

Evaluation of styrene butadiene rubber asphalt modification mechanism and adhesion effect based on molecular simulation

Design of SBS molecular structure and contribution mechanism from its soft and hard segments to modify asphalt