Abstract:It has been reported that a novel multi-component styrene-butadienestyrene composite (SBSC) modifier composed of the SBS as the main content and additional components including ethyl-vinyl-acetate (EVA), maleic anhydride grafted with ethyl-vinyl-acetate (MAH-g-EVA), naphthenic oil, and antioxidant can be produced by melt blending. This SBSC modifier can be directly mixed with bitumen and aggregate to prepare bitumen mixture, thus thoroughly addressing inferior thermal storage stability of SBS-modified bitumen. However, it is necessary to explore the efficient utilization of the SBSC modifier due to its inadequate engineering application and poor dispersion when the SBSC modifier was added directly to the bitumen mixture. The objective of this research was to investigate the feasibility of using the SBSC modifier to obtain modified bitumen with acceptable thermal storage stability and other enhanced properties. Modified bitumens (SBSC-modified bitumens with 3, 4, 5, 6, 7 % SBSC modifier content, SBS-modified bitumen with 4.5 % SBS modifier content as the control sample) were prepared. The thermal storage stability of modified bitumen was investigated by the segregation test. Besides, the basic physical properties of modified bitumen were tested, including penetration, softening point, and ductility. The rheological properties were evaluated by temperature sweep test, multiple stress creep recovery (MSCR) test, rotational viscosity (RV) test and bending beam rheometer (BBR) test, respectively. Meanwhile, fluorescence microscopy and Fourier transform infrared (FTIR) spectrometer were also applied to characterize the microproperties of the modified bitumen. Results show that the difference in softening point of SBSC-modified bitumens with modifier contents ranging from 3 % to 7 % is less than 2.5 degrees C after 72 h of high temperature storage at 163 degrees C. The softening point and ductility of SBSC-modified bitumen increase considerably with the addition of the SBSC modifier but the decrements of penetration are not significant. Besides, with the increasing addition of the SBSC modifier, complex modulus, average percent recovery, and viscosity of modified bitumen all improve. Meanwhile, phase angle, non-recoverable creep compliance of modified bitumen decrease. The flexural creep stiffness also decreases with the increasing content of the SBS modifier. When the SBS content is the same, the SBSC-modified bitumen gets better thermal storage stability, high and low temperature properties than the SBS-modified bitumen. The microproperties show that the SBSC modifier can be uniformly dispersed in base bitumen and physically mixed with the base bitumen. The SBSC-modified bitumen obtains preferable thermal storage stability. The high and low temperature properties of the bitumen are also enhanced by the addition of the SBSC modifier. Meanwhile, the melt blending method does not restrict the role of the additional components in the SBSC modifier to improve the performance of bitumen. Based on the above findings, it can be considered that the use of SBSC modifier to prepare modified bitumen with enhanced performance is a promising practice. This research may shed light on the application of SBSC modifier to bitumen pavements.

Evaluation of Storage Stability of Styrene–butadiene–styrene Block Copolymer-Modified Asphalt Via Electrochemical Analysis

Thermal storage stability and rheological properties of multi-component styrene-butadiene-styrene composite modified bitumen

Probing the Modification Mechanism of and Customized Processing Design for SBS-modified Asphalts Mediated by Potentiometric Titration

Comparative Analysis of Rheological and Microscopic Performance of SBS Modified Asphalt Based on Field Aging and Laboratory Aging

Evaluation of Rheological and Aging Behavior of Modified Asphalt Based on Activation Energy of Viscous Flow

Improved Properties of Weathered Coal and SBR/Weathered Coal Compound Modified Asphalt

Analysis of Quantification and Mechanism of SBS Modifier in SBS-Modified Asphalt

Microscopic Analysis of Aging Characteristics of SBS-Modified Asphalt Based on FTIR Technology

Laboratory Investigation of Storage Stability and Aging Resistance of Slightly SBS-Modified Bitumen Binders

Molecular simulation and experimental analysis on co-aging behaviors of SBS modifier and asphalt in SBS-modified asphalt

Rheological Properties, Compatibility, and Storage Stability of SBS Latex-Modified Asphalt

Microstructures, Thermal and Mechanical Properties of Epoxy Asphalt Binder Modified by SBS Containing Various Styrene-Butadiene Structures

Diffusion and reinforcement mechanism study of the effect of styrene/butadiene ratio on the high-temperature property of asphalt using molecular dynamics simulation

Study of the Properties and Modification Mechanism of SBS-Modified Asphalt by Dry Process

Laboratory Evaluation of Storage Stability for Asphalt Binder Modified with Crumb Rubber and Styrene–Isoprene–Styrene Depending on Evaluation Factors and Blending Condition

Study on the Performance and Modification Mechanism of Polyphosphoric Acid (PPA)/Styrene–Butadiene–Styrene (SBS) Composite Modified Asphalt

Evaluation of the Thermal Stability and Micro-Modification Mechanism of SBR/PP-Modified Asphalt

Rapid determination of styrene-butadiene-styrene (SBS) content in modified asphalt based on Fourier transform infrared (FTIR) spectrometer and linear regression analysis

Influence of Thermo-Oxidative Aging on the Properties of SBS-Modified Asphalt Binders

Storage stability performance of composite modified asphalt with scrap non-tire automotive rubber, waste plastic pyrolytic oil and sulfur

Aging Characteristics of SBS-Modified Asphalt under Thermo-Photo-Oxygen Coupling Conditions