Abstract:The effect of PEO addition on the microstructure of PLA. Today, the use of biodegradable polymers has become widespread in a wide range of industries. This research scrutinized the physical, mechanical, and rheological properties of poly (lactic acid)/poly (ethylene oxide)/carbon nanotube (PLA/PEO/CNTs) blend nanocomposites, as a good candidate for usage in the packaging industry. PEO and CNTs were added at various concentrations to improve the flexibility, toughness, gas permeability, thermal stability, and mechanical properties of PLA via solution blending. Differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), Field Emission Scanning Electron Microscope (FESEM), water contact angle (WCA), rheometric mechanical spectrometer (RMS) test, gas permeability, and tensile characterization were performed to characterize the properties of the prepared blends and nanocomposites. The experimental results revealed that the addition of 25 wt% PEO to the PLA matrix made a partially miscible blend with a droplet‐matrix morphology. PEO at this concentration increased the elongation at break (from 2.2% to 18%) while reducing the modulus (from 25 to 6 MPa). Also, the experimental results indicated that the miscibility of PLA and PEO was enhanced by the addition of 1 wt% CNTs to the prepared blend, associated with diminished entropy of mixing in the LCST phase diagram. Theoretical calculations predicted that the CNTs would be localized in the PLA phase which increased the total crystallinity of the sample by 28%, considerably reducing the amount of gas permeation into the nanocomposite. In addition, the introduction of the CNTs to the blend increased the elongation at break and tensile strength by 13% compared to pure PLA and lowered the rate of thermal degradation effectively. Also, the final results showed that the COOH‐CNTs located in the PEO phase caused a decline in the crystallinity and an increase in the gas permeability of the prepared nanocomposite. Highlights Improvement of physical properties of PLA by blending with PEO and CNTs. A deep investigation on rheological behavior of the prepared nanocomposite. Increasing the crystallinity degree of PLA/PEO blend by adding CNTs. Improvement of the miscibility between PLA and PEO in the presence of CNTs. Controlling the CNTs localization by surface modification.

Enhanced thermal stability, toughness, and electrical conductivity of carbon nanotube-reinforced biodegradable poly(lactic acid)/poly(ethylene oxide) blend-based nanocomposites

High performance poly(lactic acid)/poly(ether-block-amide) blend-based bionanocomposites containing carbon nanotubes and/or organoclay

Carbon nanotubes-filled polylactic acid/polycaprolactone biodegradable blends: Effect of the polycaprolactone viscosity and carbon nanotubes addition on the microstructure, electrical and mechanical properties

Elucidating the plasticizing effect on mechanical and thermal properties of poly(lactic acid)/carbon nanotubes nanocomposites

Effects of multi-walled carbon nanotubes (MWCNTs) on the degradation behavior of plasticized PLA nanocomposites

Improved Weathering Performance of Poly(Lactic Acid) through Carbon Nanotubes Addition: Thermal, Microstructural, and Nanomechanical Analyses

Enhanced Mechanical, Thermal and Electrical Properties of Additively Manufactured Polylactic Acid/Carbon Nanotube Polymer Nanocomposites

Effect of carbon nanotubes on the interface evolution and dielectric properties of polylactic acid/ethylene–vinyl acetate copolymer nanocomposites

Fabrication of a packaging film based on PLA blends: The evolution of physical, mechanical, and rheological properties

Effect of hydroxyl and carboxyl-functionalized carbon nanotubes on phase morphology, mechanical and dielectric properties of poly(lactide)/poly(butylene adipate-co-terephthalate) composites

Carbon Nanotube Migration in a Compatibilized Blend System, Leading to Kinetically Induced Enhancement in Electrical Conductivity and Mechanical Properties

Effect of Carbon Nanotube on Thermal, Tribological and Mechanical Properties of 3D Printing Polyphenylene Sulfide

Creating poly(lactic acid)/carbon nanotubes/carbon black nanocomposites with high electrical conductivity and good mechanical properties by constructing a segregated double network with a low content of hybrid nanofiller

Effect of Carbon Nanotubes on the Mechanical Properties and Crystallization Behavior of Poly(ether Ether Ketone)

Facile Preparation Of Modified Carbon Nanotube-Reinforced Pbt Nanocomposites With Enhanced Thermal, Flame Retardancy, And Mechanical Properties

Effect of Modified Carbon Nanotube on the Thermal Behavior, Flame Retardancy and Mechanical Properties of Poly(1,4-Butylene Terephthalate)/Aluminum Phosphinate Composites

Strong Synergistic Toughening and Compatibilization Enhancement of Carbon Nanotubes and Multi-Functional Epoxy Compatibilizer in High Toughened Polylactic Acid (pla)/poly (butylene Adipate-Co-terephthalate) (PBAT) Blends

A facile method for carbon nanotube/carbon fiber‐reinforced polylactic acid composites

Fabrication and Characterization of PLA/PBAT Blends, Blend-Based Nanocomposites, and Their Supercritical Carbon Dioxide-Induced Foams

Relationship Between Microstructure Evolution and Properties Enhancement of Carbon Nanotubes‐filled Polybutylene Terephthalate/polypropylene Blends Induced by Thermal Annealing

Improved Yield and Electrical Properties of Poly(Lactic Acid)/Carbon Nanotube Composites by Shear and Anneal