Abstract:Ultrasonic-assisted drilling (UAD) is a machining process that is known to improve the hole quality and reduce cutting forces. Previous studies focused on optimizing cutting parameters to improve the hole quality in conventional drilling (CD) and UAD, as well as to finding the optimum vibration parameters (frequency and amplitude) that will increase the effectiveness of the UAD process. However, the influence of cutting tool type during UAD has been largely overlooked. This research aims to address this gap by analyzing the effect of cutting tool type during UAD on the cutting forces and hole quality in GLARE (Glass Laminate Aluminum-Reinforced Epoxy) laminates. Four types of drills, namely, twist drill (TD), double cone drill (DCD), a step drill type 1 (SD1), and step drill type 2 (SD2) with different step length, were selected for this study. The lowest thrust force (47.04 N) and torque (0.079 Nm) were achieved using twist drill, while DCD, SD1, and SD2 exhibited higher thrust forces (12.81%, 20.69%, 41.3%) and torques (94%, 92%, 91%), respectively. In addition, TD produced high-quality holes with lowest surface roughness (R a 1.66 μm, R z 10.58 μm) and minimal burr formation (entry burr height 152.3 μm, exit burr height 69.22 μm). Conversely, DCD, SD1, and SD2 showed higher surface roughness R a (23%, 16%, 24%) and R z (16%, 37%, 29%), respectively, compared to the TD. Holes drilled using SD1 and SD2 generally had smaller burr height. Overall, UAD system effectively reduced cutting forces at low spindle speed and feed rate. To achieve higher drilling quality, specifically to reduce the surface roughness and exit burr height, a medium spindle speed of 3000 rpm, a feed rate of 225 mm/min is recommended. Drilling at higher cutting parameters using UAD resulted in a decline in hole quality, except for entry burr height.

Effect of ultrasound-assisted vibration on Ti-6Al-4V/Al2024-T351 laminated material processing with geometric tools

Study on the mechanism of AL2024-T351/Ti-6Al-4V laminated materials by ultrasonic vibration drilling

Comparative study on drilling effect between conventional drilling and ultrasonic-assisted drilling of Ti-6Al-4V/Al2024-T351 laminated material

Study on the Simulation and Experiment of Ultrasonic-assisted Vibration Drilling of Ti6Al4V

Study on tool wear in longitudinal-torsional composite ultrasonic vibration–assisted drilling of Ti-6Al-4V alloy

Evaluation of different tool geometries in the finite element simulation of ultrasonic-assisted drilling of Ti6A14V

Experimental Study on Longitudinal-Torsional Ultrasonic Vibration Drilling of Carbon Fiber–reinforced Plastics/titanium Alloy Stacks

Study on the influence of tool point angle on ultrasonic vibration–assisted drilling of titanium alloy

Influence of cutting tool design on ultrasonic-assisted drilling of fiber metal laminates

Study on chip shapes in longitudinal-torsional composite ultrasonic vibration–assisted drilling of Ti-6Al-4V

Ultrasonic assistance in drilling: FEM analysis and experimental approaches

Study on ultrasonic-assisted drilling of Ti6Al4V using 3-flute drill in the finite element simulation

Experimental investigation on cavitation effect and surface quality of ultrasonic-assisted micro-hole drilling

Unravelling the influence of vibration on material removal and microstructure evolution in ultrasonic transversal vibration-assisted helical milling of Ti-6Al-4V holes

Performance Analysis of the Longitudinal-Torsional Ultrasonic Milling of Ti-6Al-4V

Study on the mechanism and performance of longitudinal-torsional ultrasonic vibration assisted drilling CFRP/Ti stack

Investigation on cutting forces and tool wear in high-speed milling of Ti-6Al-4V assisted by longitudinal torsional ultrasonic vibrations

Simulation and experimental research on longitudinal-torsional ultrasonic vibration drilling of CFRP/Ti laminates

Introducing transversal vibration in twist drilling: Material removal mechanisms and surface integrity