Abstract:Microstructural characteristics of additively manufactured Ti-6Al-4V specimens are analyzed in this study. Laser Engineered Net Shaping technology, a direct energy deposition additive manufacturing process, is used to fabricate specimens. Effects of process parameters including machine head laser power, head write speed, layer height, hatch spacing, and powder flow rate on the morphological features of the material are investigated. A first batch of samples is built with a combination of parameters leading to full density metal parts across each layer and near-zero defects likewise more conventional process techniques (i.e. wrought and casting). A second batch of samples is built with a set of processing parameters aimed to induce defects within the parts like voids and porosity. Samples from both batches were stress-relieved in order to remove internal residual stresses generated by the additive manufacturing process. Optical microscopy, scanning electron microscopy and X-ray diffraction were used to characterize the microstructure of all samples. Tensile properties were measured after the stress-relief heat treatment. It was found that Laser Engineered Net Shaping technology parts are strongly sensitive to variations of building process parameters. Different structure morphologies were observed for different incident energies and cooling rates due to the combination of laser power and head write speed. The grain size distribution and shape are influenced by the powder flow rate resulting in either equiaxed or columnar grain microstructures with the development of material defects such as pores, gas entrapment and lack of fusion. Non-porous specimens revealed comparable tensile and ductility properties with the wrought counterpart; however, porous specimens were found to have a reduced strength and ductility.

Defect formation in titanium samples obtained by electron beam additive manufacturing

Defect Formation in Titanium Alloy during Non-stationary Process of Local Metallurgy

Influence of the Coarse Grain Structure of a Titanium Alloy Ti-4Al-3V Formed by Wire-Feed Electron Beam Additive Manufacturing on Strain Inhomogeneities and Fracture

Formation of Defects and Inhomogeneities in the Structure of Composite Materials Based on Aluminum-Manganese Bronze with an In Situ Introduction of Nickel and Titanium Alloys or Steel During Wire-Feed Electron Beam Additive Manufacturing

Investigation of the Effect of Artificial Internal Defects on the Tensile Behavior of Laser Powder Bed Fusion 17–4 Stainless Steel Samples: Simultaneous Tensile Testing and X-Ray Computed Tomography

Alloying effect of Ti-6Al-4V on composite of 321 stainless steel fabricated by electron beam additive manufacturing

Porosity effect on tensile behavior of Ti-6Al-4V specimens produced by laser engineered net shaping technology

Discovering the role of the defect morphology and microstructure on the deformation behavior of additive manufactured Ti–6Al–4V

Electron Beam Impact on Microstructure and Microhardness of Ti–6Al–4V Titanium Alloy Produced by Wire Electron-Beam Additive Manufacturing Technology and Selective Laser Alloying at Simulation of Electronic-Beam Welding

Defect formation mechanism of laser additive manufacturing joint for large-thickness Ti6Al4V titanium alloy with Y2O3 nanoparticles

Titanium Alloy Repair with Wire-Feed Electron Beam Additive Manufacturing Technology

Quantitative study of geometric characteristics and formation mechanism of porosity defects in selective laser melted Ti6Al4V alloy by micro-computed tomography

Study of pore defect and mechanical properties in selective laser melted Ti6Al4V alloy based on X-ray computed tomography

Microstructure and Properties of 3D Ti-6Al-4V Articles Produced with Advanced Co-axial Electron Beam & Wire Additive Manufacturing Technology

The role of defects and characterisation of tensile behaviour of EBM Additive manufactured Ti-6Al-4V: An experimental study at elevated temperature

Microstructure and Microhardness of Electron Beam Melted Ti-6Al-4V Components with Differential Thickness in Initial Deposition Layers

Microstructure and Mechanical Properties of TC4 Titanium Alloy by Electron Beam Freeform Fabrication

In Situ CT Tensile Testing of an Additively Manufactured and Heat-Treated Metastable ß-Titanium Alloy (Ti-5Al-5Mo-5V-3Cr)

Mechanical Behavior of Additive Manufacturing (AM) and Wrought Ti6Al4V with a Martensitic Microstructure

Effect of Heat Treatment on Microstructure and Tensile Properties of Ti-6Al-4V Alloy Produced by Coaxial Electron Beam Wire Feeding Additive Manufacturing

Additive manufacturing of titanium alloys: microstructure and texture evolution, defect formation and mechanical response