Abstract:Research interest in thin-film transistor (TFT)-based flexible electronics for next-generation foldable and rollable displays is increasing, centering on flexible plastic substrates such as polyethylene terephthalate (PET), polyethylene naphthalate (PEN), and polyimide (PI). For flexible electronics using plastic substrates, it is important to select suitable semiconductor materials that can be deposited at low substrate temperature. Metal oxide (MO) semiconductors such as indium-gallium-zinc oxide (IGZO), zinc oxide (ZnO) are attracting attention as suitable candidates for plastic substrate electronics because of their higher mobility and optical transmittance than hydrogenated amorphous silicon (a-Si:H). In addition, since it can be processed at a lower temperature than low-temperature polysilicon (LTPS), it can be easily applied to flexible plastic substrates. One of the greatest advantages of MO is that it can be easily fabricated by conventional semiconductor processing methods such as sputtering, atomic laser deposition, and solution processes. Among them, solution-processed deposition method is particularly advantageous in terms of manufacturing efficiency because it does not require a separate vacuum system, and can efficiently utilize raw materials, so the fabrication cost is inexpensive. In particular, spray pyrolysis can guarantee environmental stability, high mobility, and large area production than other solution processes. In this work, we developed the high-performance, flexible a-IGZO/Al 2 O 3 TFTs using spray pyrolysis fabricated on the flexible PI substrate. In a previous study, we developed a method to reduce curling and electrostatic discharge (ESD) damage to PI substrates by using a mixture of carbon nanotubes (CNTs) and graphene oxide (GO) between carrier glass and PI substrate. Therefore, it was possible to mechanically detach the TFTs on PI substrate and handle them easily even after detachment. The spray-pyrolyzed Al 2 O 3 film is one of the high-k dielectric materials, which can lower the operating voltage, so the low-power consumption of the TFT backplane can be realized. The flexible spray-pyrolyzed a-IGZO/Al 2 O 3 TFT exhibits the field-effect mobility (μ FE ) of 9.75 cm 2 V −1 s −1 , threshold voltage (V TH ) of −0.8 V, subthreshold swing (SS) of 0.29 V dec −1 , and on/off current ratio of 6.2 × 10 7 . Even without TFT passivation layer, it shows environmental stability. The TFTs show robust electrical performance even under tensile strain with a bending radius of 1 mm. In addition, it showed stable electrical characteristics even in the repeated bending test of 30,000 cycles under compressive strain with a bending radius of 1 mm. This is due to fewer defects resulting from the smooth interface of the a-IGZO film and the Al 2 O 3 film deposited through spray pyrolysis. Therefore, spray-pyrolyzed a-IGZO/Al 2 O 3 TFT fabricated on PI substrate is a promising candidate for next-generation foldable display application. Figure 1

A prototype active-matrix OLED using graphene anode for flexible display application

Large-scale plasma patterning of transparent graphene electrode on flexible substrates

Carrier Transport Regulation of Pixel Graphene Transparent Electrodes for Active‐Matrix Organic Light‐Emitting Diode Display

Oxide TFT with multilayer gate insulator for backplane of AMOLED device

Roll-to-roll Production of 30-Inch Graphene Films for Transparent Electrodes

Microscale‐Patterned Graphene Electrodes for Organic Light‐Emitting Devices by a Simple Patterning Strategy

31-Inch 4K Flexible Display Employing Gate Driver With Metal Oxide Thin-Film Transistors

An Aqueous Process for Preparing Flexible Transparent Electrodes Using Non-Oxidized Graphene/Single-Walled Carbon Nanotube Hybrid Solution

Extremely efficient flexible organic solar cells with a graphene transparent anode: Dependence on number of layers and doping of graphene

Pushing the conductance and transparency limit of monolayer graphene electrodes for flexible organic light-emitting diodes

Quasi- Freestanding" Graphene- On- Single Walled Carbon Nanotube Electrode for Applications in Organic Light- Emitting Diode

30 inch Roll-Based Production of High-Quality Graphene Films for Flexible Transparent Electrodes

Wetting-Induced Fabrication of Graphene Hybrid with Conducting Polymers for High-Performance Flexible Transparent Electrodes

Stretchable, Transparent Graphene Interconnects for Arrays of Microscale Inorganic Light Emitting Diodes on Rubber Substrates

Large-scale pattern growth of graphene films for stretchable transparent electrodes

Organic/Inorganic Hybrid Thin-Film Encapsulation Using Inkjet Printing and PEALD for Industrial Large-Area Process Suitability and Flexible OLED Application.

Textile Display with AMOLED Using a Stacked-Pixel Structure on a Polyethylene Terephthalate Fabric Substrate

Recent Developments in Flexible Organic Light‐Emitting Devices

Stably doped graphene transparent electrode with improved light-extraction for efficient flexible organic light-emitting diodes

Flexible Amorphous Indium-Gallium-Zinc Oxide Thin-Film Transistor with Aluminum Oxide Gate Insulator on Polyimide Substrate By Spray Pyrolysis for Foldable Display

Novel biodegradable and ultra-flexible transparent conductive film for green light OLED devices