Abstract:The aluminum dross (AD), which causes numerous problems of its management and disposal to environment is a useful resource to extract alumina. This study explains a novel process to extract highly pure alumina (Al2O3) from AD at a high extraction rate without producing the residues and exhaust gases. An experimental set up was designed to perform the grinding of AD for the decomposition of aluminum nitride (AlN) and the removal of salts. Thereby, the desalted dross was used to detect the optimum alkaline (NaOH) calcination parameters and leaching conditions, as well as the dissolution kinetics of alumina and silica. The leaching residues were used to produce Ettringite mineral with calcium-based compounds (including CaO and CaSO4) to avoid the problems of solid waste disposal from the leaching process. Moreover, to purify the alumina, slightly soluble CaSO4 was added in leaching solution to precipitate silicate and the optimum additive/solution ratio (g/mL) was determined. The aluminum hydroxide (Al(OH)3), precipitated after the carbonization was calcinated at 900.0 °C for 2 h to produce γ-alumina. The morphological and mineralogical characterizations of AD, γ-Al2O3 and the synthesized Ettringite mineral were studied by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM) and X-ray fluorescence (XRF). It was observed that activation temperature of 1000.0 °C, Na2O/Al2O3 molar ratio of 1.4, leaching temperature of 60.0 °C, leaching time of 40.0 min, and the leaching liquid/solid ratio (mL/g) of 25/1 were the optimal parameter conditions to extract alumina with the extraction rate at 86.7% and purity of more than 98%. The results of leaching kinetics' study showed that the dissolution of alumina and silica were both controlled by layer diffusion process with the apparent activation energy of 11.4010 kJ·mol-1 and 2.0556 kJ·mol-1, respectively.

Purification of fused alumina by high temperature calcination in vacuum

PURIFICATION OF TAN RAI ALUMINUM HYDROXIDE WITH ACETIC ACID AND PREPARATION OF HIGH PURE NANOSIZE α-ALUMINA

Extraction of alumina from aluminum dross by a non-hazardous alkaline sintering process: Dissolution kinetics of alumina and silica from calcined materials

Low temperature sintering of α-alumina with the aid of abrasive powder in wet grinding

Removal of impurities for the synthesis of high-property alumina-spinel ceramic from secondary aluminum dross

Vacuum Carbothermic Reduction of Alumina

Effect of trace alumina on mechanical, dielectric, and ablation properties of fused silica ceramics

Effect of Pore Size Distribution of Carbon‐Covered Alumina on the Preparation of Submicrometer Α‐alumina Powders

Technology for High Pure Aluminum Oxide Production from Aluminum Scrap

High Temperature Thermal Stabilization of Alumina Modified by Lanthanum Species

Low-Calcination Temperature to Synthesize A-Alumina From Aluminium Waste Can Using Sol-Gel Method

Preparation of High-purity Alumina via Hydrolysis of Aluminum Isopropoxide after Desilication with Lanthanum Oxide

Preparation And Characterization Of Gamma-Al2o3 By Polyaluminum Chloride With High Al-13 Content

Recovery of iron and calcium aluminate slag from high-ferrous bauxite by high-temperature reduction and smelting process

Synthesis of submicronic α-alumina from local aluminum slags

Synthesis and sintering behavior of a nanocrystalline α-alumina powder

Synthesis and characterization of activated alumina with high thermal stability by a low-heat solid-phase precursor method

Kinetics Study of Al Extraction from Desilicated Coal Fly Ash by NaOH at Atmospheric Pressure

Preparation of High Purity Alumina Technology Overview

PREPARATION AND CHARACTERIZATION OF ALUMINA NANOCRYSTALLINE POWDER BY COMPLEXING SOL-GEL METHOD

Study on the Vacuum Degassing Behavior of 99% Alumina Ceramic