Abstract:When the local heat flux exceeds specified flux limit, tungsten PFC surfaces can be damaged, which is not acceptable for a reliable reactor operations. The divertor PFCs are typically designed for a specific heat flux limit usually assuming an average steady-state heat flux which is typically 5–10 MW/m 2 . However, in addition to steady-state heat flux, fusion reactor divertor PFCs could experience transient heat fluxes such as ELMs and/or other magnetic reconnection events which can deposit large transient heat fluxes onto the divertor PFCs. The transient divertor heat flux could be significantly larger than the steady-state heat flux which could damage the solid PFC surfaces. The divertor heat flux can be subjected to additional complications such as the uncertainties in the the divertor strike point heat flux projection. Moreover, there are additional experimental observations of non-axisymmetric power flux which can occur under non-axisymmetric magnetic perturbations. The liquid lithium (LL) PFCs is more resilient against such transient heat fluxes as they could evaporate LL as needed and the lost LL can be then replenished afterward. In this paper, we analyze a case for a transient divertor heat pulse of 1 MJ in 10 ms for a ITER-size reactor. This is a small perturbation (~ 0.1%) to the expected plasma stored energy compared to the previously analyzed case of 20 MJ heat pulse. Even with this relatively modest heat pulse, the LL surface undergoes ~ 100 °C temperature rise. However, the resulting LL surface heating without rapid cooldown mechanism could lead to excessive LL evaporation continuing well after the transient heat flux resulting in a significant Li injection of ~ 0.6 mol in about a 200 ms period. This amount of Li injection could cause plasma dilution and performance degradation. On the other hand, an active Li injection capability if optimized could prevent the LL surface temperature rise and thus reducing subsequent Li evaporation into the plasma by a factor of 7 compared to the passive LL PFC case. A crucial tool of active Li injection is a rapid response pellet injector which could inject light impurity pellets before the excessive heat flux could reach the divertor plate causing serious damage. A simple pellet ablation model suggests a favorable pellet deposition profile for smaller ~ 0.1 mm radius pellet with ~ 10–20 m/s velocity. Moreover, if it is possible to inject from the private flux region, the pellet injection efficiency into the high heat flux strike point region can be as high as 80% compared to ~ 50% for the injection from outer radius region. The pellet deposition efficiency can be further improved by designing a shell-pellet which can burst when a certain ablation fraction is reached. A possible implementation technique using an inductive pellet injector with a rapid time response of a few msec is proposed here which can be tested in NSTX-U.

Vapor shielding of liquid lithium divertor target during steady state and transient events

Predictive modeling of a lithium vapor box divertor in NSTX-U using SOLPS-ITER

Influence of hydrogen content in tokamak scrape-off-layer on performance of lithium divertor

Simulation of lithium flow, redeposition, and vapor shielding in liquid lithium divertor of T-15MD tokamak with SOLPS 4.3 code

Optimization of lithium vapor box divertor evaporator location on NSTX-U using SOLPS-ITER

Active Radiative Liquid Lithium Divertor for Handling Transient High Heat Flux Events

Active Lithium Injection for a Real Time Control of the Divertor Heat Flux for Fusion Devices

Thermal Response of ARIES-I Divertor Plate to Plasma Disruption

A comparative study of the effects of liquid lithium and tin as DEMO divertor targets on the heat loads and SOL properties

The design of 3D-printing liquid lithium divertor target plate and its interaction with high-density plasma

Design study of helium-solid suspension cooled blanket and divertor plate for a tokamak power reactor

Investigation of ELM-related Larmor ion flux into toroidal gaps of divertor target plates

Oscillatory vapour shielding of liquid metal walls in nuclear fusion devices

Monte Carlo/molecular Dynamics Simulation on Melting and Evaporating Processes of Material Due to Laser Irradiation

Experimental, Numerical and Analytical Evaluation of J×b -Thrust for Fast-Liquid-metal-flow Divertor Systems of Nuclear Fusion Devices

Scaling of HeatLMD-simulated impurity outflux from COMPASS-U liquid metal divertor

An improved understanding of the roles of atomic processes and power balance in divertor target ion current loss during detachment

Deuterium retention in co-deposition with lithium in Magnum-PSI: experimental analysis and comparison with SOLPS-ITER

Analysis and design of Fast Flow Liquid Li Divertor for Fusion Nuclear Science Facility (FNSF) using coupled plasma boundary and LM MHD/heat transfer codes

Physics basis for the first ITER tungsten divertor

Impact of repetitive ELM transients on ITER divertor tungsten monoblock top surfaces