Abstract:Pulse-jet bag filters are frequently employed for particle removal from off gases. Separated solids form a layer on the permeable filter media called filter cake. The cake is responsible for increasing pressure drop. Therefore, the cake has to be detached at a predefined upper pressure drop limit or at predefined time intervals. Thus the process is intrinsically semi-continuous. The cake formation and cake detachment are interdependent and may influence the performance of the filter. Therefore, understanding formation and detachment of filter cake is important. In this regard, the filter media is the key component in the system. Needle felts are the most commonly used media in bag filters. Cake formation studies with heat treated and membrane coated needle felts in pilot scale pulse jet bag filter were carried out. The data is processed according to the procedures that were published already [Powder Technology, Volume 173, Issue 2, 19 April 2007, Pages 93-106]. Pressure drop evolution, cake height distribution evolution, cake patches area distribution and their characterization using fractal analysis on different needle felts are presented here. It is observed that concavity of pressure drop curve for membrane coated needle felt is principally caused by presence of inhomogeneous cake area load whereas it is inherent for heat treated media. Presence of residual cake enhances the concavity of pressure drop at the start of filtration cycle. Patchy cleaning is observed only when jet pulse pressure is too low and unable to provide the necessary force to detach the cake. The border line is very sharp. Based on experiments with limestone dust and three types of needle felts, for the jet pulse pressure above 4 bar and filtration velocity below 50 mm/s, cake is detached completely except a thin residual layer (100-200 μm). Uniformity and smoothness of residual cake depends on the surface characteristics of the filter media. Cake height distribution of residual cake and newly formed cake during filtration prevails. The patch size analysis and fractal analysis reveal that residual cake grow in size (latterly) following regeneration initially on the base with edges smearing out, however, the cake heights are not leveled off. Fractal dimension of cake patches boundary falls in the range of 1-1.4 and depends on vertical position as well as time of filtration. Cake height measurements with Polyimide (PI) needle felts were hampered on account of its photosensitive nature.

Characterization of the fibrous filter media used in a baghouse phosphate dust collector by scanning electron microscopy

Individual element mapping of baghouse phosphate dust collector deposits

Study on the Filtration Performance of the Baghouse Filters for Ultra-Low Emission as a Function of Filter Pore Size and Fiber Diameter

Investigation of Fiber-Based Bag Filter Coated with Metal Oxides for Dust Adsorption

Measurement of the Nanoparticles Distribution in Flat and Pleated Filters During Clogging

Development of an asymmetric composite PPS-based bag-filter material through membrane laminating and superfine fiber blending: Lab test, field application and development of numerical models

Experimental investigation on filtration characteristic with different filter material of bag dust collector for dust removal

High fidelity simulation of ultrafine PM filtration by multiscale fibrous media characterized by a combination of X-ray CT and FIB-SEM

Experimental Study on Structure and Performance of Dedusting Filter Material Modified by Reducing Graphene Oxide Spraying

Characterization of Airborne Particles Collected from Car Engine Air Filters Using SEM and EDX Techniques

Utilizing Electrostatic Effect in Fibrous Filters for Efficient Airborne Particles Removal: Principles, Fabrication, and Material Properties

Effect of filtration pressure on the particle penetration efficiency of fibrous filter media

Electrostatic Enhancement of the Collection Efficiency of Stainless Steel Fiber Filters

Effect of filter microstructure on filtration characteristics in a nonwoven bag filter: A resolved CFD-DEM approach coordinated with X-ray computed tomography image

Preparation of Anti-Layered Polyamide-66/Polyacrylonitrile/Polyethersulfone (Pa-66/Pan/pes) Sandwich Structured Membrane for Air Filtration by Electrospinning

Phosphate Mine Tailing Recycling in Membrane Filter Manufacturing: Microstructure and Filtration Suitability

Experimental study of cake formation on heat treated and membrane coated needle felts in a pilot scale pulse jet bag filter using optical in-situ cake height measurement

Efficient nanoparticles removal and bactericidal action of electrospun nanofibers membranes for air filtration

Porous filtering media comparison through wet and dry sampling of fixed bed gasification products

Development of a double-layered ceramic filter for aerosol filtration at high-temperatures: The filter collection efficiency

Electrospun 3D Curly Electret Nanofiber Air Filters for Particulate Pollutants