Abstract:Despite boasting giant leaps in performance improvement over the years, the current commercial standard, Li-ion batteries, are fast approaching their theoretical limits. Meanwhile, Lithium-Sulfur (Li-S) batteries offering ultra-high theoretical energy density (~2600 Whkg -1 ), cost-effectiveness, and nontoxicity are being seen as promising alternatives. Despite their plentiful advantages, the practicality of Li-S batteries has been largely stymied by several challenges: a) deleterious polysulfide dissolution and ‘shuttle effect’, b) significant volume change of S cathodes during cycling, c) safety concerns with flammable traditional glyme-based electrolyte, and d) the instability of Li anode. To mitigate these challenges, researchers have explored all-solid-state electrolytes, but their poor Li-ion conductivity, high interfacial impedance, and need for expensive, exotic materials and complex fabrication procedures severely limit their practical application. To overcome these challenges, we propose an in-situ gelled polymer-ceramic hybrid silsesquioxane-based electrolyte system. The gelled matrix, thermally crosslinked post cell fabrication, immobilizes the glyme-based liquid electrolyte and exhibits high liquid-like ionic conductivities (1.03 mS.cm -1 ), low interfacial impedance, and high oxidative potential (>4.5V vs. Li/Li + ) . In this study, in addition to vastly decreased flammability, we report superior Li-ion conductivity compared to state-of-art solid-state Li-S electrolytes. This high ionic conductivity translated to a significantly improved specific capacity of 1050 mAh.gS -1 at 0.2 C, elevated Coulombic efficiencies (>98.5%), and elevated rate kinetics. The gelled electrolytes exhibited stable cycling in a large temperature range (-10 o C - 60 o C). Moreover, polysulfide permeation studies and subsequent DFT calculations revealed that the gelled electrolyte exhibited strong chemical absorptivity to lithium polysulfides due to the polar silsesquioxane core, which translated to superior capacity retention (>80% over 200 cycles). Further, post- mortem XPS characterization studies revealed the formation of stable SEI at the anode and cathode, and SEM of cycled anodes showed reduced dendritic formations. Finally, the electrolyte was tested in practical pouch cell architecture, and the cells demonstrated excellent reliability even under mechanical stress. This work successfully reports a robust, rationally designed gelled electrolyte system for developing safe and high-performance quasi-solid state Li-S batteries.

Ethylene Carbonate Grafted Polysilane with Different Substitutions: A New Series of Electrolyte Additives to Improve High-Temperature Performance of Lithium-Ion Batteries

The Cooperative Effect of Vinylene Carbonate and 1,3-Propane Sultone on the Elevated Temperature Performance of Lithium Ion Batteries

A Polysiloxane-Enabled Ternary Eutectic Electrolyte with Fast Ion Transport under Extreme Conditions

Tuning thin-film electrolyte for lithium battery by grafting cyclic carbonate and combed poly(ethylene oxide) on polysiloxane.

Bicomponent Electrolyte Additive Excelling Fluoroethylene Carbonate for High Performance Si-based Anodes and Lithiated Si-S Batteries

Enhancing Interfacial Properties on Silicon-Graphite Anode by Alkenyl-Functionalization of Fluorinated Cyclotriphosphazene in High-Voltage Lithium-Ion Batteries

Advanced Polymer Electrolyte with Enhanced Electrochemical Performance for Lithium-Ion Batteries: Effect of Nitrile-Functionalized Ionic Liquid

Thermal Safety Evaluation of Silane Polymer Compounds as Electrolyte Additives for Silicon-Based Anode Lithium-Ion Batteries

Prop-1-ene-1,3-sultone As Interfacial-Engineering Additive in Nonflammable Electrolyte for 4.45 V LiCoO2/Si-Graphite 2 /Si-Graphite Lithium-Ion Batteries with High Performance

Gel Polymer Electrolyte Enables Low-Temperature and High-Rate Lithium-Ion Batteries via Bionic Interface Design

Polysiloxane/Poly(vinylidene fluoride)‐co‐Hexafluoropropylene Polymer Blend‐based Lithium‐Ion Conducting Polymer Electrolytes for Room‐Temperature Lithium‐Metal Batteries

Rational Design of an In-Build Quasi-Solid-state Electrolyte for High-Performance Lithium-Ion Batteries with the Silicon-Based Anode

Novel Composite Electrolyte Additive for Enhancing the Thermal and Cycling Stability of SiO/C Anode Li-ion Battery

Effects of electrolyte additive on the electrochemical performance of Si/C anode for lithium-ion batteries

A Single-Ion Gel Polymer Electrolyte System for Improving Cycle Performance of LiMn2O4 Battery at Elevated Temperatures

Rationally Designed in-Situ Gelled Polymer-Ceramic Hybrid Electrolyte Enables Superior Performance and Stability in Quasi-Solid-State Lithium-Sulfur Batteries

High-Energy Metallic Lithium Batteries Enabled by Polymer-in-Salt Electrolytes of Cyclic Carbonate Substituted Polyethers

Improvement of lithium-ion battery performance at low temperature by adopting polydimethylsiloxane-based electrolyte additives

Slidable and Highly Ionic Conductive Polymer Binder for High‐Performance Si Anodes in Lithium‐Ion Batteries

Hybrid lithium salts regulated solid polymer electrolyte for high-temperature lithium metal battery

Enhancing high-temperature storage performance for the commercial lithium-ion battery via a effective addtive strategy