Abstract:In this research, we focused on the investigation of the structural, surface, and corrosion behavior properties of copper-loaded TiO2 nanotubular array surfaces that were further deposited with a chitosan biopolymer. This composite material was fabricated on Ti6Al4V alloy substrates using a combination of anodic oxidation (AO), electro-cathodic deposition (ECD), and electrophoretic deposition (EPD) techniques, primarily to apply it in medical implant contexts. Initially, the TiO2 nanotubes were prepared via anodization (AO). Subsequently, copper was introduced into the TiO2 nanotubes through electro-cathodic deposition (ECD), followed by the coating of chitosan over the copper-loaded TiO2 nanotubes using electrophoretic deposition (EPD). To comprehensively assess the characteristics of these surfaces, a series of analytical techniques were employed, including SEM, EDX mapping, XRD, and wettability measurements. Furthermore, the electrochemical properties of these surfaces, namely the OCP, PDP, and EIS, were extensively scrutinized. The outcomes of this investigation directed a notable development in the electrochemical corrosion resistance of the chitosan-deposited copper-loaded TiO2 nanotubular array surfaces in comparison to uncoated Ti6Al4V alloy, particularly under conditions simulating a physiological environment (simulated body fluid, SBF). Corrosion rates, assessed through PDP (Potentiodynamic Polarization) curves, were determined to be 0.3023 mm/y for polished Ti6Al4V, 0.1476 mm/y for TiO2 30 V 4 h, 0.1235 mm/y for TNT-Cu2/30/Ch, 0.0733 mm/y for TNT-Cu2/60/Ch, and 0.0611 mm/y for TNT-Cu2/90/Ch. Additionally, corrosion protection efficiencies were calculated as 51.16 % for TiO2 30 V 4 h, 59.15 % for TNT-Cu2/30/Ch, 75.76 % for TNT-Cu2/60/Ch, and 79.81 % for TNT-Cu2/90/Ch. Notably, the TNT-Cu2/90/Ch sample demonstrated a significantly low corrosion rate of 0.0611 mm/year and a high corrosion protection efficiency of 79.81 %. This enhancement can happen due to the chitosan coating, which acts as a protective layer, hindering the ingress of the physical solution into the original metal surfaces. Notably, TNT-Cu2/90/Ch coated sample exhibited a corrosion rate (icorr) approximately 5 times lower than that of the uncoated alloy. In conclusion, this study presents a novel chitosan-coated composite material consisting of copper-loaded TiO2 nanotubular surfaces that effectively enhances corrosion resistance compared to polished Ti6Al4V substrates.

Protection of copper from corrosion through electrodeposited poly-2,5-dimercapto-1,3,4-thiadiazole–TiO2 composite film

ELECTROCHEMICAL, DFT AND MULTISCALE SIMULATION STUDIES ON SELF-ASSEMBLED FILMS OF 2-AMINO-4-METHYL-PYRIDINE INHIBITOR FOR COPPER METAL CORROSION PROTECTION IN 3.5% NaCl MEDIUM

Electrosynthesized conducting poly(1,5-diaminonaphthalene) as a corrosion inhibitor for copper

Long-term protective mechanism of poly(N-methylaniline)/phosphate one-step electropolymerized coatings for copper in 3.5% NaCl solution

Ambient-stable polyethyleneimine functionalized Ti3C2T nanohybrid corrosion inhibitor for copper in alkaline electrolyte

Stabilized Ti3C2T -doped 3D vesicle polypyrrole coating for efficient protection toward copper in artificial seawater

High Performance Organic Coatings of Polypyrrole Embedded with Manganese Iron Oxide Nanoparticles for Corrosion Protection of Conductive Copper Surface

3,4-Dimethoxy phenyl thiosemicarbazone as an effective corrosion inhibitor of copper under acidic solution: comprehensive experimental, characterization and theoretical investigations

Anticorrosion Protection of New Composite Coating for Cobalt-Based Alloy in Hydrochloric Acid Solution Obtained by Electrodeposition Methods

Surface Protection Of Copper By Self-Assembly Of Novel Poly(5-Methylenebenzotriazol-N-Yl)

Preparation of Triazole Compounds Via Click Chemistry Reaction and Formation of the Protective Self-Assembled Membrane Against Copper Corrosion

A novel process for copper protection in the simulated industrial cooling water based on click synthesis and self‐assembling method

Fabricated Super-Hydrophobic Film with Potentiostatic Electrolysis Method on Copper for Corrosion Protection

Composite protective effect of benzotriazole and 2-mercaptobenzothiazole on electroplated copper coating

Structural and corrosion analysis of copper/chitosan coating on nanotubular TiO2/Ti6Al4V implant surface

In Situ Click-Assembling Monolayers on Copper Surface with Enhanced Corrosion Resistance

In-situ preparation of triazole polymerization films on copper surface via SI-ATRP method and their performance against copper corrosion

Remarkable improvement of corrosion resistance of silane composite coating with Ti3C2Tx MXene on copper

Enhancing the corrosion inhibition of copper sheets in oil-in-water (O/W) emulsions by combining two organic heterocyclic derivatives

Surface-initiated atom transfer radical polymerization of triazole monomer from copper surface and its anticorrosion performance

Designing a smart epoxy anti-corrosion coating loaded with molybdate-doped polythiophene nano-hybrid self-assembled multi-walled carbon nanotube