Abstract:Background Context Stabilization of the occipitocervical (OC) junction with posterior instrumentation plays a vital role in addressing a spectrum of pathologies. Due to limited bone surfaces of the occiput and C1 lamina, achieving union across the OC junction is challenging. Purpose To explore the biomechanics and a clinical series of patients treated with multi-rod constructs across the OC junction using a novel occipital plate with single- and dual-headed, modular tulip heads. Study Design/Setting Biomechanical analysis and retrospective case series. Patient Sample Adults at a single institution who underwent posterior cervical multi-rod constructs across the OC junction. Outcome Measures OC-C4 range of motion (ROM), maximum von Mises stress on the rods, and adjacent segment ROMs and intradiscal parameters. Patient demographics, revision operations, rod breakages, wound complications. Methods A validated occiput-cervical finite element (FE) model was used to simulate OC-C4 cervical fixation under multi-directional pure moment loading. A total of 4 rod configurations were simulated: (A) 2-rod-Ti (4.0 mm titanium rods); (B) 2-rod-CoCr (3.5 mm cobalt chrome rods); (C) 3-rods (4.0 mm titanium rods); (D) 4-rods (4.0 mm titanium rods). The aforementioned measures were compared. A retrospective analysis was also performed of adults at a single institution who underwent posterior cervical multi-rod constructs across the OC junction. Results Biomechanically, lowest primary rod stresses were observed for 3- and 4-rod constructs. Compared to 2-rod-Ti (121.8 MPa), 2-rod-CoCr showed a 43.2% stress increase in the rods, while 3- and 4-rods experienced rod stress reductions of 20% and 23.2%, respectively. No appreciable differences in OC-C4 ROM, C4-5 ROM, and C4-5 discal stresses were found between multi-rod and 2-rod constructs. Maximum occipital and C4 screw stresses were decreased in multi-rod constructs compared to 2-rods, with least stresses noted in the 4-rod construct. Maximum plate stresses were slightly increased in the 4-rod construct compared to 2- and 3-rod fixation, though the forces were largely similar among the constructs.Ten patients (average age 66.4 ± 10.6 years; 8 males) were assessed clinically. Nine of the ten operations were for primary stabilization of pathological fractures and associated craniocervical and/or atlantoaxial instability using 4-rods across the OC junction. At an average follow-up time of 1.58 ± 0.5 years (range, 1 - 2.3 years), there were no instrumentation failures, no adjacent segment failures, and no wound complications. Conclusions In this proof-of-concept investigation, multiple rods (3- and 4-rods) across the OC junction using a novel occipital plate with single- and dual-headed, modular tulips was safe and effective in stabilizing the OC junction. Accompanying FE analysis demonstrated that multi-rod constructs decreased primary rod stresses and had lower stresses on occipital and C4 screws compared to 2-rod constructs, while occipital plate stresses were largely similar. Additional clinical studies are needed to confirm these findings and to determine the ultimate utility of multi-rod constructs across the OC junction.

Multiple-rod constructs in adult spinal deformity surgery for pelvic-fixated long instrumentations: an integral matched cohort analysis

Multiple-Rod Constructs in Adult Spinal Deformity Surgery: A Systematic Review and Meta-Analysis

Use of multiple rods and proximal junctional kyphosis in adult spinal deformity surgery

Impact of multi-rod reinforcement on rod fractures in adult spinal deformity: A retrospective case series with a minimum follow up of 5 years

Biomechanical evaluation of multiple pelvic screws and multirod construct for the augmentation of lumbosacral junction in long spinal fusion surgery

Quantitative Biomechanical Evaluation for Optimal Spinal Instrumentation to Prevent Mechanical Complications in Spinal Fusion from the Lower Thoracic Spine to the Pelvis for Adult Spinal Deformity: A Finite Element Analysis

Long additional rod constructs can reduce the incidence of rod fractures following 3-column osteotomy with pelvic fixation in short term

The Influence of Increased Pedicle Screw Diameter and Thicker Rods on Surgical Results in Adolescents Undergoing Posterior Spinal Fusion for Idiopathic Scoliosis

Preoperative Robotics Planning Facilitates Complex Construct Design in Robot-Assisted Minimally Invasive Adult Spinal Deformity Surgery—A Preliminary Experience

Patient-Specific Rods in Adolescent and Adult Spinal Deformity Surgery: A Narrative Review

Systematic review and meta-analysis for the impact of rod materials and sizes in the surgical treatment of adult spine deformity

Comprehensive In Silico Evaluation of Accessory Rod Position, Rod Material and Diameter, Use of Cross-connectors, and Anterior Column Support in a Pedicle Subtraction Osteotomy Model: Part II: Effects on Lumbosacral Rod and Screw Strain

Factors associated with rod fracture following surgery for adult spinal deformity: a single-center retrospective study

Multi-Rod Posterior Occipitocervical Instrumentation Constructs: A Biomechanical Analysis and Initial Case Series of 10 Patients with Complex Craniocervical Pathology

The Effect of Rod Pattern, Outrigger, and Multiple Screw-Rod Constructs for Surgical Stabilization of the 3-Column Destabilized Cervical Spine - A Biomechanical Analysis and Introduction of a Novel Technique

Biomechanical Comparison of Unilateral and Bilateral Pedicle Screw Fixation after Multilevel Lumbar Lateral Interbody Fusion

Biomechanical assessment of the stabilization capacity of monolithic spinal rods with different flexural stiffness and anchoring arrangement

Randomized Trial of Augmented Pelvic Fixation in Patients Undergoing Thoracolumbar Fusion for Adult Spine Deformity: Initial Results from a Multicenter Randomized Trial

Multilevel Stabilization Screws Prevent Proximal Junctional Failure and Kyphosis in Adult Spinal Deformity Surgery: A Comparative Cohort Study

Biomechanical Differences Between Transfacet and Lateral Mass Screw-Rod Constructs for Multilevel Posterior Cervical Spine Stabilization