Abstract:The techniques for releasing thermal energy accumulated in periods of high availability to meet the demand in periods of low energy supply contribute to the continuity of the cycles involved in thermodynamic processes. In this context, phase change materials are capable of absorbing and releasing large amounts of energy in relatively short periods of time and under specific operating conditions. However, phase change materials have low thermal conductivity and need to be coupled with high-thermal-conductivity materials so that the heat flux can be intensified and the energy absorption and release times can be controlled. This work aims to numerically study the solidification process of a phase change material inserted into a triplex tube heat exchanger with finned copper walls to intensify the thermal exchange between the phase change material and the cooling heat transfer fluid, water, that will receive the energy accumulated in the material. This work proposes the 3D numerical modeling of the triplex tube heat exchanger with finned walls and meets the need for numerical models that allow for the analysis of the full geometry of the latent heat thermal energy storage system and the thermal and fluid dynamic phenomena that are influenced by this geometry. Results of the temperature, liquid fractions and velocity fields during phase transformations are presented, analyzed and validated with experimental data, presenting average errors of below 5%. The total material discharge time was approximately 168 min, necessary for the complete solidification of the phase change material, with water injected into the triplex tube heat exchanger at a flow rate of 8.3 L/min and a temperature of 68 °C. The solidification process occurred more slowly in the same direction as the length of the triplex tube heat exchanger, and from 80% of the material in the solid state, the difference between the solidification time for z = 0 and z = 480 mm was 30 min. The fluid dynamic conditions developed in the latent heat thermal energy storage system promoted a maximum negative heat flux of −6423 w/m2 to the annular internal surface and −742 w/m2 to the annular external surface, representing a heat removal process nine times less intense on the external surface. The total energy released to the cooling heat transfer fluid was 239.56 kJ/kg.

Effect of the time-dependent volumetric heat flux on heat transfer performance inside a heat sink based on the phase change materials

Transient Performance of a Thermal Energy Storage-Based Heat Sink Using a Liquid Metal As the Phase Change Material

Numerical Investigation of Heat Transfer Characteristics in a Shell- And-Tube Latent Heat Thermal Energy Storage System

Numerical simulation of heat transfer performance in an enclosure filled with a metal foam and nano-enhanced phase change material

Radiative Heat Transfer to Enhance the Performance of Liquid Metal-Based Phase Change Heat Sink under Natural Convection Condition

Experimental and numerical investigations on the intermittent heat transfer performance of rectangular cavity plate fin phase change material based heat sink

Numerical and experimental study of inverse natural convection heat transfer for heat sink in a cavity with phase change material

Investigation on the Melting Performance of a Phase Change Material Based on a Shell-and-Tube Thermal Energy Storage Unit with a Rectangular Fin Configuration

Experimental Investigation into the Effect of Fin Shapes on Heat Dissipation Performance of Phase Change Heat Sink

Experimental Study on the Thermal Performance of a Finned Metal Foam Heat Sink with Phase Change Material

Thermal performance of phase change material–based heat sink for passive cooling of electronic components: An experimental study

Thermal design of a novel heat sink cooled by natural convection with phase transition in the series loop

Thermal response to periodic heating of a heat sink incorporating a phase change material

3D Numerical Analysis of a Phase Change Material Solidification Process Applied to a Latent Thermal Energy Storage System

Numerical investigation and optimisation of solid–solid phase change material composite-based plate-fin heat sink for thermal management of electronic package

Numerical Investigation of Heat Transfer in Wire and Tube based Phase Change Material Heat Exchanger

Numerical study on the effects of fin parameters on the charging process of PCM-based heat sink

Experimental and Numerical Investigations on a Phase Change Material Based Heat Sink with Symbiotically Joined Heat Pipe

Numerical investigation of the impact of toothed fins on the heat transfer performance of a shell-and-tube exchanger during phase change material melting process

Velocity field measurement and heat transfer characteristics of the melting process under constant heat flux

Thermal Performance of a Phase Change Material-Based Heat Sink Subject to Constant and Power Surge Heat Loads: A Numerical Study