Electrode Properties of Various Nano-Fibrous Carbons

Minato Egashira,Masahiro Tokita,Mizue Itoh,Nobuko Yoshimoto,Masayuki Morita

DOI: https://doi.org/10.1149/ma2011-02/11/516

2011-08-01

ECS Meeting Abstracts

Abstract:Abstract not Available.

What problem does this paper attempt to address?

In Situ Transmission Electron Microscopy Study of Electrochemical Sodiation and Potassiation of Carbon Nanofibers

Ying Liu,Feifei Fan,Jiangwei Wang,Yang Liu,Hailong Chen,Katherine L. Jungjohann,Yunhua Xu,Yujie Zhu,David Bigio,Ting Zhu,Chunsheng Wang

DOI: https://doi.org/10.1021/nl500970a

IF: 10.8

2014-01-01

Nano Letters

Abstract:Carbonaceous materials have great potential for applications as anodes of alkali-metal ion batteries, such as Na-ion batteries and K-ion batteries (NIB and KIBs). We conduct an in situ study of the electrochemically driven sodiation and potassiation of individual carbon nanofibers (CNFs) by transmission electron microscopy (TEM). The CNFs are hollow and consist of a bilayer wall with an outer layer of disordered-carbon (d-C) enclosing an inner layer of crystalline-carbon (c-C). The d-C exhibits about three times volume expansion of the c-C after full sodiation or potassiation, thus suggesting a much higher storage capacity of Na or K ions in d-C than c-C. For the bilayer CNF-based electrode, a steady sodium capacity of 245 mAh/g is measured with a Coulombic efficiency approaching 98% after a few initial cycles. The in situ TEM experiments also reveal the mechanical degradation of CNFs through formation of longitudinal cracks near the c-C/d-C interface during sodiation and potassiation. Geometrical changes of the tube are explained by a chemomechanical model using the anisotropic sodiation/potassiation strains in c-C and d-C. Our results provide mechanistic insights into the electrochemical reaction, microstructure evolution and mechanical degradation of carbon-based anodes during sodiation and potassiation, shedding light onto the development of carbon-based electrodes for NIBs and KIBs.
Length-dependent Electrical and Thermal Properties of Carbon Nanotube-Loaded Epoxy Nanocomposites

Michael Russ,Sameer S. Rahatekar,Krzysztof Koziol,Benjamin Farmer,Hua-Xin Peng

DOI: https://doi.org/10.1016/j.compscitech.2013.03.011

IF: 9.1

2013-01-01

Composites Science and Technology

Abstract:Sonication-induced scission was used to obtain carbon nanotubes (CNTs) with aspect ratios averaging 50 (short CNTs) and 500 (long CNTs). A series of carbon nanotube/epoxy nanocomposite samples with CNT content up to 1.0wt.% were prepared using these tubes. Electrical and thermal characterisation was conducted to identify changes in such properties and the extent of these changes as a function of aspect ratio and CNT content. Results show significantly enhanced electrical conductivities and a modest increase in the thermal conductivities in both sets of samples. Further analysis of electrical conductivity of the long CNT and short CNT-based epoxy nanocomposites was carried out in order to understand their viability for EMI shielding and electrostatic dissipation applications. The processing behaviour of the long and short CNT-based composites and the corresponding electrical properties is also discussed which will help the researchers to select the right type of carbon nanotube aspect ratio achieve specific electrical properties as well as good processing behaviour.
Carbon Nanomaterials for Electrochemical Capacitors

Yury Gogotsi

DOI: https://doi.org/10.1149/ma2011-02/11/482

2011-08-01

ECS Meeting Abstracts

Abstract:Abstract not Available.
Electrosorption Capacitance of Nanostructured Carbon-Based Materials

Chia-Hung Hou,Chengdu Liang,Sotira Yiacoumi,Sheng Dai,Costas Tsouris

DOI: https://doi.org/10.1016/j.jcis.2006.06.009

IF: 9.9

2006-01-01

Journal of Colloid and Interface Science

Abstract:The fundamental mechanism of electrosorption of ions developing a double layer inside nanopores was studied via a combination of experimental and theoretical studies. A novel graphitized-carbon monolithic material has proven to be a good electrical double-layer capacitor that can be applied in the separation of ions from aqueous solutions. An extended electrical double-layer model indicated that the pore size distribution plays a key role in determining the double-layer capacitance in an electrosorption process. Because of the occurrence of double-layer overlapping in narrow pores, mesopores and micropores make significantly different contributions to the double-layer capacitance. Mesopores show good electrochemical accessibility. Micropores present a slow mass transfer of ions and a considerable loss of double-layer capacitance, associated with a shallow potential distribution inside pores. The formation of the diffuse layer inside the micropores determines the magnitude of the double-layer capacitance at low electrolyte concentrations and at conditions close to the point of zero charge of the material. The effect of the double-layer overlapping on the electrosorption capacitance can be reduced by increasing the pore size, electrolyte concentration, and applied potential. The results are relevant to water deionization.
Electrochemical Properties of Carbon Nanofibers As the Negative Electrode in Lithium-Ion Batteries

Shohei Maruyama,Guangzheng Zhuang,Hongyu Wang,Tomokazu Fukutsuka,Kohei Miyazaki,Takeshi Abe,Takayuki Doi,Zempachi Ogumi

DOI: https://doi.org/10.1016/j.carbon.2013.02.010

2013-01-01

TANSO

Abstract:Carbon nanofibers were prepared by the exfoliation of natural graphite flake in a propylene carbonate solution containing a lithium salt and sonication. The electrochemical behavior of the carbon nanofibers used as the negative electrode in lithium-ion batteries was investigated. Carbon nanofibers heat-treated at 600 °C had a diameter of several tens of nanometers. From X-ray diffraction measurements and Raman spectroscopy, it was found that a graphitic structure derived from natural graphite flake remained in the carbon nanofibers. Carbon nanofibers heat-treated at 400 °C showed a higher reversible capacity than NG-7 (natural graphite powder) and a rapid response in the cyclic voltammogram. This is on account of the nanosize effect. The best electrochemical performance among all the carbon nanofibers was obtained by heat treatment at 400 °C. The rate performance of the carbon nanofiber heat-treated at 400 °C was also examined.
Ultrathin carbon nanotube fibrils of high electrochemical capacitance.

Jun Ma,Jie Tang,Han Zhang,Norio Shinya,Lu-Chang Qin

DOI: https://doi.org/10.1021/nn900787h

IF: 17.1

2009-01-01

ACS Nano

Abstract:We have assembled single-wall carbon nanotubes into ultrathin long fibrils using a dielectrophoretic technique and studied the mechanical and electrochemical properties of carbon nanotube fibrils. The diameter of the fibrils can be controlled in the range of 200 nm to 2 mum, and the length can reach as long as 1 cm. The obtained fibrils have a tensile strength of about 65 MPa, electrical conductivity ranging from 80 to 200 S cm(-1), and specific capacitance more than 200 F g(-1). The results indicate that these ultrathin long carbon nanotube fibrils are of great potential for applications as conductive wires and probe electrodes.
Polyacrylonitrile-Based Electrospun Carbon Paper for Electrode Applications

Ying Yang,Fritz Simeon,T. Alan Hatton,Gregory C. Rutledge

DOI: https://doi.org/10.1002/app.35485

IF: 3

2011-01-01

Journal of Applied Polymer Science

Abstract:Polyacrylonitrile (PAN)-based carbon paper with fiber diameters of 200-300 nm was developed through hot-pressing, pre-oxidation and carbonization of electrospun fiber mats. Changes in morphology, crystallinity, and surface chemistry of the hot-pressed carbon paper were investigated. More junctions between fibers were formed with increasing hot-press time, which is attributed to melting and bonding of fibers. The bulk density of such an electrode increased to 0.5-0.6 g/cm, which could help to improve the volume energy density. The conductivity of the carbon paper was found to be about 40 S/cm when the surface area was approximately 2 m/g, and depends not only on the conductivity of the individual nanofibers but also on the contacts between the nanofibers. The performance of the electrospun carbon paper as an electrode for electrochemical reactions involving ferrocene molecules was affected by the preparation protocol: the higher surface area of the electrodes formed with shorter hot-press times provided a higher current generated per unit mass than that obtained with electrodes prepared using longer hot-press time, but electrodes prepared with longer hot-press times exhibited higher electrical conductivity and faster electron transfer kinetics.
The Fabrication of Carbon Nanofibers Paper Supported CoO4 Nanocomposite and Their Electrochemical Properties

Fuliang Zhu,Jingxin Zhao,Yongliang Cheng,Xingbin Yan

DOI: https://doi.org/10.1166/jnn.2015.9494

Abstract:A hierarchical network architecture consisting of Co3O4 nanoflakes network (nanonet) coats on a carbon fiber paper. For this 3 dimension (3D) architecture, the electrode shows ideal pseudocapacitive behavior and the maximum specific capacitance of 210 F/g can be reached at the constant current density of 1 A/g in 1 M KOH electrolyte, still retaining 85% of the initial capacitance after 1000 cycles of repeating charge-discharge. The improved capacity may be attributed to the unique hierarchical network structures, which improve electron/ion transport, enhancing the kinetics of redox reactions and facilitate facile stress relaxation during cycling.
The electronic transport properties and microstructure of carbon nanofiber/epoxy composites

Aïssa Allaoui,Suong V. Hoa,Martin D. Pugh

DOI: https://doi.org/10.48550/arXiv.0802.4189

2008-02-28

Materials Science

Abstract:Carbon nanofibres (CNF) were dispersed into an epoxy resin using a combination of ultrasonication and mechanical mixing. The electronic transport properties of the resulting composites were investigated by means of impedance spectroscopy. It was found that a very low critical weight fraction (pc = 0.064 wt %) which may be taken to correspond to the formation of a tunneling conductive network inside the matrix. The insulator-to-conductor transition region spanned about one order of magnitude from 0.1 to 1 wt %. Far from the transition, the conductivity increased by two orders of magnitude. This increase and the low value of the conductivity were explained in terms of the presence of an epoxy film at the contact between CNF. A simple model based on the CNF-CNF contact network inside the matrix was proposed in order to evaluate the thickness of that film.
Polyacrylonitrile-based carbon nanofiber electrode fabricated via electrospun for supercapacitor application

Sumit Dubal,Sachin Chavan,Gaurav Lohar,Prasad Lokhande,Udayabhaskar Rednam,Deepak Kumar

DOI: https://doi.org/10.1177/23977914241232161

2024-02-27

Proceedings of the Institution of Mechanical Engineers Part N Journal of Nanoengineering and Nanosystems

Abstract:Proceedings of the Institution of Mechanical Engineers, Part N: Journal of Nanomaterials, Nanoengineering and Nanosystems, Ahead of Print. The versatile properties of electrospun carbon nanofibers gaining attention for electrode materials for supercapacitors. The heat treatment process of stabilization played an important role before the carbonization process in electrode fabrication. In the present study, electrospun stabilized polyacrylonitrile nanofiber (St PAN) and carbonized Polyacrylonitrile nanofiber (CNF) at minimum temperature were used as active mass for supercapacitor electrodes. Stabilized CNF nanofiber sample showed a reduction in nanofiber diameter with increased carbon percentage. XRD results showed increased crystallinity in the CNF sample as compared with the Stabilized PAN sample. Electrochemical characterization was performed to measure specific capacitance and to analyze the charge storage mechanism. The proportion of capacitive and diffusion-controlled contributions to energy storage was estimated using Dunn's model. The results obtained demonstrated that, in comparison to the St PAN electrode, the CNF electrode exhibited a greater capacitive-controlled contribution. The CNF sample has shown an increased capacitive contribution of 82.3% as compared with the St PAN sample. This work provides a method for making electrospun carbon nanofiber-based electrodes as well as a methodical methodology for examining the charge storage process.
Carbon nanofibers prepared via electrospinning

Michio Inagaki,Ying Yang,Feiyu Kang

DOI: https://doi.org/10.1002/adma.201104940

IF: 29.4

2012-01-01

Advanced Materials

Abstract:Carbon nanofibers prepared via electrospinning and following carbonization are summarized by focusing on the structure and properties in relation to their applications, after a brief review of electrospinning of some polymers. Carbon precursors, pore structure control, improvement in electrical conductivity,and metal loading into carbon nanofibers via electrospinning are discussed from the viewpoint of structure and texture control of carbon.
Electroactivate Shape-Memory Polymer Filled With Nanocarbon Particles And Short Carbon Fibers

Jinsong Leng,Haibao Lv,Yanju Liu,Shanyi Du

DOI: https://doi.org/10.1063/1.2790497

IF: 4

2007-01-01

Applied Physics Letters

Abstract:In addition to the fabrication of shape-memory thermoset polymer nanocomposites filled with conductive nanoparticles and fiber fillers, this paper is focused on factors which would influence the electrical property of this type of material. It is shown that the particulate additives are dispersed homogeneously within the matrix and served as interconnections between the fibers, while the fibrous additives act as long distance charge transporter by forming local conductive paths. The electrical conductivity of the nanocomposite which contains 5 wt % carbon nanoparticles and 2 wt % short carbon fiber is 2.32 S/cm by four-point van der Pauw method, and can be induced by 24 V voltages. (C) 2007 American Institute of Physics.
Multi-dimensional carbon nanofibers for supercapacitor electrodes

Byung Gwan Hyun,Hye Jeong Son,Sangyoon Ji,Jiuk Jang,Seung-Hyun Hur,Jang-Ung Park

DOI: https://doi.org/10.1007/s10832-016-0055-9

2016-12-10

Journal of Electroceramics

Abstract:Four different types of porous carbon nanofibers (CNFs), plain, hollow, multi-channel (MC), and hollowed MC, were fabricated using coaxial electrospinning and thermal treatment for supercapacitor electrodes. The influence of the porosity on the specific surface area (SSA), pore volumes, and electrochemical propoerties of porous CNFs were investigated. The comparisons of their properties are a valuable work with same methods, becuase electrochemical performances are depending on the measurement conditions. Among them, the hollowed MC CNF structure was indicated the highest SSA and pore volumes. In addition, their hybrid structures with multi-walled carbon nanotubes (MWCNTs) were analyzed in therms of their porosity, SSA, and electrochemical properties for supercapacitors (specific capacitance and long-term cycling). These hybrid structures can improve overall porosity and electrochemical propoerties due to the extra mesoporous structures formed by entangling MWCNTs. In conclusion, these porous CNFs have a promising potential for various fields which need high porosity and SSA, and can be used as the platforms for catalysts, sensors, or energy devices.

materials science, ceramics
Nanostructured Carbon Fibres (NCF): Fabrication and Application in Supercapacitor Electrode

Kabir O. Oyedotun,Katlego Makgopa,Thabo T. Nkambule,Mkhulu K. Mathe,Kabir O. Otun,Bhekie B. Mamba

DOI: https://doi.org/10.3390/polym16131859

IF: 5

2024-06-29

Polymers

Abstract:A facile interconnected nanofibre electrode material derived from polybenzimidazol (PBI) was fabricated for a supercapacitor using a centrifugal spinning technique. The PBI solution in a mixture of dimethyl acetamide (DMA) and N, N-dimethylformamide (DMF) was electrospun to an interconnection of fine nanofibres. The as-prepared material was characterised by using various techniques, which include scanning electron microscopy (SEM), X-ray diffractometry (XRD), Raman, X-ray photoelectron spectroscopy (XPS), and Brunauer–Emmett–Teller (BET) among others. The specific surface area of the interconnected NCF material was noticed to be around 49 m2 g−1. Electrochemical properties of the material prepared as a single-electrode are methodically studied by adopting cyclic voltammetry, electrochemical impedance spectroscopy, and constant-current charge–discharge techniques. A maximum specific capacitance of 78.4 F g−1 was observed for the electrode at a specific current of 0.5 A g−1 in a 2.5 M KNO3 solution. The electrode could also retain 96.7% of its initial capacitance after a 5000 charge–discharge cycles at 5 A g−1. The observed capacitance and good cycling stability of the electrode are supported by its specific surface area, pore volume, and conductivity. The results obtained for this material indicate its potential as suitable candidate electrode for supercapacitor application.

polymer science
Nitrogen, Boron and Fluorine Tri-Doped Carbon Nanotubes on Carbon Cloth As the Electrode Materials for Supercapacitors

Yishan Xu,Mingjun Xiao,Tingting Liu,Renpeng Lin,Yanshuang Meng,Yue Zhang,Fuliang Zhu

DOI: https://doi.org/10.1016/j.jelechem.2023.117812

IF: 4.598

2023-01-01

Journal of Electroanalytical Chemistry

Abstract:In this study, nitrogen, boron, and fluorine co-doped carbon nanotubes (NBF-CNT) was growth on carbon cloth (CC) through a simple in situ method. The material was used directly as electrodes for supercapacitors and tested for its electrochemical performance. The electrode exhibited an area specific capacitance of 4303.2 mF/cm2 (322.7F/g) at 2 mA/cm2 (0.15 A/g), maintaining 77.4% capacity at 20 mA/cm2. At 10 mA/cm2, the flexible electrode retained 97.8% capacitance after 8000 charge/discharge cycles. Assembled into a symmetrical supercapacitor, the electrodes achieved an area specific capacity of 750.8 mF/cm2 (56.3F/g) at 2 mA/cm2 (0.15 A/g), with energy densities of 104.3 mu Wh/cm2 (7.8 Wh/kg) and 61.4 mu Wh/cm2 (4.6 Wh/kg) at power densities of 1000 mu W/cm2 (75 W/kg) and 10,000 mu W/cm2 (750 W/kg), respectively. The excellent electrochemical performance attibutes two factors: (1) binder-free electrode preparation, mitigating issues related to poor conductivity and low active substance utilization; and (2) the synergistic effect of multi-heteroatom doping in carbon nanotubes, enhancing electrode conductivity and hydrophilicity.
Photoelectrochemical properties of TiO2 coated on carbon nanofibers with different microstructure film electrodes

Zhizhou Li,Xiaoli Cui,Junsheng Zheng,Qingfei Wang

2008-01-01

Abstract:Novel nanocomposites of TiO2 and two kinds' carbon nanofibers with different, microstructure were prepared by sol-gel method. The nanocomposites were studied via SEM, XRD, and photoelectrochemistry. The potential dependence of photocurrent and the photocurrent transient's indicate that the nanocomposite shows characteristics of n-type semiconductor. The experimental results demonstrate that the PCNF/TiO2 shows a higher photoelectrochemical response and sensitivity for visible light illumination than FCNF/TiO2, and pristine TiO2,. This,is likely because of the specific microstructure of the PCNF, which possesses large numbers of active edge sites and provides many favorable sites for electron transfer as well as a very large working surface area. The significant enhancement of the photoelectrochemical response of the CNF toward visible light responses may result from the difference of their morphologies as well as their textural properties and crystalline structure. The results show that PCNF and FCNF are thus very promising candidates for developing a class of ideal and novel modified photoelectrodes.
Ultrathin porous NiCo2O4 nanosheet arrays on flexible carbon fabric for high-performance supercapacitors.

Jun Du,Gang Zhou,Haiming Zhang,Chao Cheng,Jianmin Ma,Weifeng Wei,Libao Chen,Taihong Wang

DOI: https://doi.org/10.1021/am4017335

IF: 9.5

2013-01-01

ACS Applied Materials & Interfaces

Abstract:NiCo2O4 with higher specific capacitance is an excellent pseudocapacitive material. However, the bulk NiCo2O4 material prevents the achievement of high energy desity and great rate performance due to the limited electroactive surface area. In this work, NiCo2O4 nanosheet arrays were deposited on flexible carbon fabric (CF) as a high-performance electrode for supercapacitors. The NiCo2O4 arrays were constructed by interconnected ultrathin nanosheets (10 nm) with many interparticle pores. The porous feature of NiCo2O4 nanosheets increases the amount of electroactive sites and facilitates the electrolyte penetration. Hence, the NiCo2O4/CF composites exhibited a high specific capacitance of 2658 F g(-1) (2 A g(-1)), good rate performance, and superior cycling life, suggesting the NiCo2O4/CF is a promising electrode material for flexible electrochemical capacitors.
Mesoporous Carbon Nanofibers for Supercapacitor Application

Kaixue Wang,Yonggang Wang,Yarong Wang,Eiji Hosono,Haoshen Zhou

DOI: https://doi.org/10.1021/jp807463u

2009-01-01

Abstract:Mesoporous carbon nanofibers have been prepared by a confined self-assembly of triblock copolymers with soluble low molecular weight phenolic resol within the channels of anodic alumina membranes. SEM and TEM observations showed that hexagonally arranged mesoporous channels were coiled concentrically around the longitudinal axis of the carbon nanofibers. These carbon nanofibers with BET surface area over 1424 m(2) g(-1) have been used as electrode materials for electrochemical capacitors tested in KOH and EC/DEC electrolyte solutions. Compared to mesoporous carbon prepared from the same precursor sol, these one-dimensional nanofibers could provide a shortened diffusion distance for electrolyte ions. The better performance of these mesoporous nanofibers greatly benefited from their high specific surface area, shortened diffusion distance, mesoporous openings on the outer surface, and well-controlled pore size. These mesoporous carbon nanofibers have been proved to be promising electrode materials for electrochemical supercapacitors in high-rate charge/discharge operations.
MOF-derived nanoporous carbons with diverse tunable nanoarchitectures

Minjun Kim,Ruijing Xin,Jacob Earnshaw,Jing Tang,Jonathan P. Hill,Aditya Ashok,Ashok Kumar Nanjundan,Jeonghun Kim,Christine Young,Yoshiyuki Sugahara,Jongbeom Na,Yusuke Yamauchi

DOI: https://doi.org/10.1038/s41596-022-00718-2

IF: 14.8

2022-09-10

Nature Protocols

Abstract:Metal-organic frameworks (MOFs), or porous coordination polymers, are crystalline porous materials formed by coordination bonding between inorganic and organic species on the basis of the self-assembly of the reacting units. The typical characteristics of MOFs, including their large specific surface areas, ultrahigh porosities and excellent thermal and chemical stabilities, as well as their great potential for chemical and structural modifications, make them excellent candidates for versatile applications. Their poor electrical conductivity, however, has meant that they have not been useful for electrochemical applications. Fortuitously, the direct carbonization of MOFs results in a rearrangement of the carbon atoms of the organic units into a network of carbon atoms, which means that the products have useful levels of conductivity. The direct carbonization of zeolitic imidazolate framework (ZIF)-type MOFs, particularly ZIF-8, has successfully widened the scope of possible applications of MOFs to include electrochemical reactions that could be used in, for example, energy storage, energy conversion, electrochemical biosensors and capacitive deionization of saline water. Here, we present the first detailed protocols for synthesizing high-quality ZIF-8 and its modified forms of hollow ZIF-8, core-shell ZIF-8@ZIF-67 and ZIF-8@mesostuctured polydopamine. Typically, ZIF-8 synthesis takes 27 h to complete, and subsequent nanoarchitecturing procedures leading to hollow ZIF-8, ZIF-8@ZIF-67 and ZIF-8@mPDA take 6, 14 and 30 h, respectively. The direct-carbonization procedure takes 12 h. The resulting nanoporous carbons are suitable for electrochemical applications, in particular as materials for supercapacitors.

biochemical research methods
Synthesis of multi-branched porous carbon nanofibers and their application in electrochemical double-layer capacitors

X.Y. Tao,X.B. Zhang,L. Zhang,J.P. Cheng,F. Liu,J.H. Luo,Z.Q. Luo,H.J. Geise

DOI: https://doi.org/10.1016/j.carbon.2005.11.024

IF: 10.9

2006-01-01

Carbon

Abstract:Multi-branched carbon nanofibers with a porous structure have been synthesized on a Cu catalyst doped with Li, Na, or K. The products were characterized by field emission scanning electron microscopy, transmission electron microscopy, high-resolution transmission electron microscopy and Raman spectroscopy. Using this new type of nanofiber as polarized electrodes, an electrochemical double-layer capacitor with a specific capacitance of ca. 297F/g was obtained using 6M KOH as the electrolyte.

Electrode Properties of Various Nano-Fibrous Carbons

In Situ Transmission Electron Microscopy Study of Electrochemical Sodiation and Potassiation of Carbon Nanofibers

Length-dependent Electrical and Thermal Properties of Carbon Nanotube-Loaded Epoxy Nanocomposites

Carbon Nanomaterials for Electrochemical Capacitors

Electrosorption Capacitance of Nanostructured Carbon-Based Materials

Electrochemical Properties of Carbon Nanofibers As the Negative Electrode in Lithium-Ion Batteries

Ultrathin carbon nanotube fibrils of high electrochemical capacitance.

Polyacrylonitrile-Based Electrospun Carbon Paper for Electrode Applications

The Fabrication of Carbon Nanofibers Paper Supported CoO4 Nanocomposite and Their Electrochemical Properties

The electronic transport properties and microstructure of carbon nanofiber/epoxy composites

Polyacrylonitrile-based carbon nanofiber electrode fabricated via electrospun for supercapacitor application

Carbon nanofibers prepared via electrospinning

Electroactivate Shape-Memory Polymer Filled With Nanocarbon Particles And Short Carbon Fibers

Multi-dimensional carbon nanofibers for supercapacitor electrodes

Nanostructured Carbon Fibres (NCF): Fabrication and Application in Supercapacitor Electrode

Nitrogen, Boron and Fluorine Tri-Doped Carbon Nanotubes on Carbon Cloth As the Electrode Materials for Supercapacitors

Photoelectrochemical properties of TiO2 coated on carbon nanofibers with different microstructure film electrodes

Ultrathin porous NiCo2O4 nanosheet arrays on flexible carbon fabric for high-performance supercapacitors.

Mesoporous Carbon Nanofibers for Supercapacitor Application

MOF-derived nanoporous carbons with diverse tunable nanoarchitectures

Synthesis of multi-branched porous carbon nanofibers and their application in electrochemical double-layer capacitors