Abstract:The hydrophilic extractives isolated from black alder (Alnus glutinosa) bark through hot water extraction were characterized as novel renewable macromonomers capable of forming polyurethane (PU) networks based on a commercial polyisocyanate, with partial or complete replacement of petroleum-derived polyol polyether. The bark-sourced bio-polyol mainly consists of the xyloside form of the diarylheptanoid oregonin, along with oligomeric flavonoids and carbohydrates, resulting in a total OH group content of 15.1 mmol·g−1 and a molecular weight (Mn) of approximately 750 g∙mol−1. The 31P NMR data confirmed a similar proportion of aliphatic OH and phenolic groups. Three-component PU compositions were prepared using polyethylene glycol (Mn = 400 g∙mol−1), bio-polyol (up to 50%), and polymeric diphenylmethane diisocyanate, which were pre-polymerized in tetrahydrofuran (THF) solution with tin organic and tertiary amine catalysts. The resulting mixture was cast and subjected to thermal post-curing. Calculation and experimental data confirmed the crosslinking activity of the bark-sourced bio-polyol in PU, leading to an increase in glass transition temperature (Tg), a decrease in sol fraction yield upon leaching of cured PU networks in THF, a significant increase in Young's modulus and tensile strength. The macromonomers derived from bark promoted char formation under high temperature and oxidative stress conditions, limiting heat release during macromolecular network degradation compared to bio-polyol-free PU. It was observed that amine catalysts, which are active in urethane formation with phenolic groups, promoted the formation of PU with higher Tg and modulus at tensile but with less limitation of heat liberation during PU macromolecular structure degradation. The high functionality of the bark-derived bio-polyol, along with the equal proportion of phenolic and aliphatic OH groups, allows for further optimization of PU characteristics using three variables: increasing the substitution extent of commercial polyethers, decreasing the NCO/OH ratio, and selecting the type of catalyst used.

Synthesis of Eugenol-Based Polyols via Thiol–Ene Click Reaction and High-Performance Thermosetting Polyurethane Therefrom

Novel Polyethylene‐b‐polyurethane‐b‐polyethylene Triblock Copolymers: Facile Synthesis and Application

Preparation and Properties of Epoxided Hydroxyl-terminated Polybutadiene Based Polyurethane Elastomers

Synthesis and Characterization of Eugenol‐based Silicone Modified Waterborne Polyurethane with Excellent Properties

Synthesis of Cardanol-Based Polyols Via Thiol-ene/Thiol-epoxy Dual Click-Reactions and Thermosetting Polyurethanes Therefrom

New biobased high functionality polyols and their use in polyurethane coatings

Facile synthesis of polyester-polyether block copolyols for the sustainable high-performance polyurethane reactive hot melt adhesives

Synthesis of biobased polyphenols for preparing phenolic polyurethanes with self-healing properties

New Insight on the Study of the Kinetic of Biobased Polyurethanes Synthesis Based on Oleo-Chemistry

Use of Polyols of Petroleum Chemical Processing as Raw Materials for the Synthesis of Polyurethanes

Synthesis of α,ω-Primary Hydroxyl-Terminated Polyether Polyols Using Prussian Blue Analogs as Catalysts

Soybean-Based Polyol as a Substitute of Fossil-Based Polyol on the Synthesis of Thermoplastic Polyurethanes: The Effect of Its Content on Morphological and Physicochemical Properties

Impact of Bark-Sourced Building Blocks as Substitutes for Fossil-Derived Polyols on the Structural, Thermal, and Mechanical Properties of Polyurethane Networks

High-performance castor oil-based polyurethane thermosets: Facile synthesis and properties

Synthesis Of Soy-Polyols Using A Continuous Microflow System And Preparation Of Soy-Based Polyurethane Rigid Foams

Eugenol-DOPO: A Bio-Based Phosphorous-Containing Monomer for Thiol-ene Photocurable Thermosets

Synthesis and Characterization of Novel Thermosetting Polyphosphazene‐urethanes

Synthesis of eugenol‐based monomers for sustainable epoxy thermoplastic polymers

Effects of Polyether and Polyester Polyols on the Hydrophobicity and Surface Properties of Polyurethane/Polysiloxane Elastomers

Poly(silyl ether-sulfone-urethane)s: toward preparation of polyurethanes with high glass transition temperature