Abstract:The advent of new materials and technologies in building materials has changed the way of building. New lighter materials with easier application methods and improved mechanical behaviors, have become necessary for the market. Moreover, the new environmental policy (2022) aims to transform the waste management into sustainable materials management to ensure the long-term protection and improvement of the environment. For the brick and tile industry, raw materials and the additives that compose the product mixture seem to be a key factor in this direction. Furthermore, every product type (solid or perforated brick) requires different additives to achieve the properties that are postulated by the international standards. For the study, the wide range of additives that were used have been assorted into three (3) categories: the inert materials, the lightweight materials, and the industrial remains. Totally, eight (8) different materials were used as additives into ceramic mass, in different proportions each time. Almost all additives used for this research were pore-forming agents. These burn out almost completely before reaching the full-fire temperature, and do not change the fired body. As a result of additives burnt out, the necessary pore volume is formed in the fired brick body, which, if combined with an appropriate percentage of voids, result in raw density readings. The pore structure is significant as long as the ultimate strength of lightweight bricks is acceptable. In this study, additives between 3 and 25% by weight were added to the clay mixture. The extrusion of specimens in solid form was carried out using the Laboratory’s vacuum press. Firstly, the extrusion of specimens from the original raw material was implemented. Secondly, it was made on the material mixed with the additives mentioned above. A series of experimental activities were followed to determine the variations of the mechanical and physical properties as well as their production procedures (extrusion, drying, and firing). According to five (5) key properties measured in the current study and compared with the mixture without additives, it was found that the variation in thermal conductivity improvement is between -11% and 19%. The bending strength of the fired products showed a decrease from 16% to 55% except for the addition of bauxite residue, which increased the strength by 8%. Bigot drying sensitivity decreased from 11% to 27%. The density in two cases increased from 2% to 7% while in the majority the mixtures with the additives showed a decrease in density from 1% to 14%. Finally, the addition of the necessary water for shaping during extrusion showed a variation from a 10% decreased to a 14% increased water.

Influence of sawdust particle size on fired clay brick properties

Characteristics of fired clay bricks with pumice additive

Thermo-physical and Mechanical Properties of Clay Bricks Produced for Energy Saving

Evaluation of physical and mechanical properties of fired-clay bricks incorporating both mineral and organic wastes

Efficient Recovery of Solid Waste Units as Substitutes for Raw Materials in Clay Bricks

Effect of Non-Plastic Raw Materials Particle Size on Technological Properties of the Single-Fired Wall Tile Bodies

Mechanical Properties of Fireclay Bricks from Binaliw Clay

Investigation of Physical-Mechanical Properties and Microstructure of Mortars with Perlite and Thermal-Treated Materials

Microstructural, physical and mechanical behavior of pastes containing clays and alumina waste

The use of mineralogical indicators for the assessment of firing temperature in fired-clay bodies

Low-cost northern Tunisian kaolinitic clay-based refractory materials and effect of a rich alumina clay addition

Reuse of walnut shell waste in the development of fired ceramic bricks

Effect of Control Technology on Properties of Quartz Porous Brick

The Influence of the Burning Environment on the Properties of Ceramic Products Based on Fusible Raw Materials

Influence of mineral composition and firing temperature on the micro- and mesoporosity of replicate archaeological ceramics

A Comparative Study on Hygric Properties and Compressive Strength of Ceramic Bricks

Influence of Solid Waste Material Content on the Properties of Steel Slag-Waste Clay Brick Ceramic Bricks

Production and characterization of natural clay-free green building brick materials using water treatment sludge and oak wood ash

Sintering effects on the development of mechanical properties of fired clay ceramics

A Simulation and Experimental Investigation of the Thermal Characteristics of Refractory Bricks Produced Using Fireclay and Agroforestry Wastes

The Effect of Bone Ash on the Physio-Chemical and Mechanical Properties of Clay Ceramic Bricks