Abstract:The effect of nitrogen content on the formation of an equiaxed solidification structure of Fe-16Cr steel was investigated. Moreover, two different kinds of refractory materials, i.e., alumina and magnesia, were employed to control the type of oxide inclusion. The characteristics of TiN(-oxide) inclusions were quantitatively analyzed in both molten steel and solidified samples. When the melting was carried out in the alumina refractory, the grain size continuously decreased with increasing nitrogen content. However, a minimum grain size was observed at a specific nitrogen content (approx. 150 ppm) when the steel was melted in the magnesia refractory. Most of the single TiN particles had a cuboidal shape and fine irregularly shaped particles were located along the grain boundary due to the microsegregation of Ti at the grain boundary during solidification. The type of TiN-oxide hybrid inclusion was strongly affected by the refractory material where Al2O3-TiN and MgAl2O4-TiN hybrid-type inclusions were obtained in the alumina and magnesia refractory experiments, respectively. The formation of oxide inclusions was well predicted by thermochemical computations and it was commonly found that oxide particles were initially formed, followed by the nucleation and growth of TiN. When the nitrogen content increased, the number density of TiN linearly increased in the alumina refractory experiments. However, the number of TiN exhibits a maximum at about [N] = 150 ppm, at which a minimum grain size was obtained in the magnesia refractory experiments. Therefore, the larger the number density of TiN, the smaller the primary grain size after solidification. The number density of TiN in the steel melted in the magnesia refractory was greater than that in the steel melted in the alumina refractory at given Ti and N contents, which was due to the lower planar lattice disregistry of MgAl2O4-TiN interface rather than that of Al2O3-TiN interface. When ∆TTiN (= difference between the TiN precipitation temperature and the liquidus of the steel) was 20 K to 40 K, the number density of effective TiN was maximized and thus, the grain size was minimized after solidification. Finally, although most of the TiN particles were smaller than 1 μm in the molten steel samples irrespective of the nitrogen content, TiN particles larger than 10 μm were observed in the solidified samples when the nitrogen content was greater than 150 ppm. The growth of TiN particles during melting and solidification was well predicted by the combinatorial simulation of the ‘Ostwald ripening model’ based on the Lifshitz–Slyozov–Wagner theory in conjunction with the ‘Diffusion controlled model’ using Ohnaka’s microsegregation equation.

Control of Coarse Precipitates of Titanium Nitride in High-Strength Low-Alloy Steel

Control of TiN precipitation behavior in titanium-containing micro-alloyed steel

Precipitation Behavior of TiN During the Solidification of High-Titanium Steel

Study on the Formation and Control of TiN Inclusion in Mushy Zone for High Ti Microalloyed Steel

The investigation of precipitation behavior of titanium compounds for high titanium steel based on in situ observation

Study on the Dissolution and Precipitation Behavior of Self-Designed (NbTi)C Nanoparticles Addition in 1045 Steel

Effect of Ce content on the microstructure and TiN precipitation behaviour of high-titanium steel during slow cooling solidification

In Situ Observation of the Precipitation, Aggregation, and Dissolution Behaviors of TiN Inclusion on the Surface of Liquid GCr15 Bearing Steel

Effect of Magnesium Content on Precipitation Behavior of TiN-Containing Inclusions in High-Titanium High-Strength Steel

Strain-induced Precipitation Kinetics of Nb(C,N) and Precipitates Evolution in Austenite of Nb–Ti Micro-Alloyed Steels

Study on Precipitation and Growth of TiN in GCr15 Bearing Steel during Solidification

Influence of Ti content on mechanical properties of low carbon steel

Carbide Precipitation in Austenite of a Titanium-Tungsten-Bearing Low-Carbon Steel

On the novel precipitation sequence of the TiN modified Al-Mn-Sc alloy processed by laser powder bed fusion

Strain-induced Precipitation in a Ti Micro-Alloyed HSLA Steel

Strengthening of Ni-Mn-Cu-Al-Co steel by nanoscale Cu and β-NiAl co-precipitated couples

Precipitation Behavior of Ti in High Strength Steels

Characterization and Control of Secondary Phase Precipitation of Nb-V-Ti Microalloyed Steel during Continuous Casting Process

Thermodynamic and Kinetic Analysis of TiN Precipitation in Nickel-Based Superalloys During Solidification

Synergistic Effect of Nitrogen and Refractory Material on TiN Formation and Equiaxed Grain Structure of Ferritic Stainless Steel

Reaction-induced nano-sized TiC in additive manufactured Ni-Co based superalloy