Abstract:This study utilizes a lab-developed pneumatic-extrusion condensing 3D food printer to prepare astragalus–starch mixed gels by blending different ratios of astragalus polysaccharide and wheat starch and applies these gels to 3D printing experiments. The aim of this paper is to investigate the impacts of mixed-gel concentrations on printing outcomes in order to identify the optimal blending ratio. Under this rationale, the effects of printing layer height and nozzle diameter on print quality were studied. Single-factor analysis and response surface methodology were employed to optimize the experiments and determine the optimal printing process parameters for the astragalus–starch mixed gels. The results indicate that an increase in astragalus polysaccharide content leads to a decrease in the sedimentation rate of the mixed gels and a tendency towards a more fluid consistency. After storage of samples in a sealed space for equal durations, it was found that an increase in astragalus polysaccharide content enhances the textural properties of the mixed gels, with optimal printing effects achieved at a 2% polysaccharide content. The optimal print quality is achieved when the ratio of nozzle diameter to layer height is between 0.5 and 0.55. The influence order of printing process parameters on the overall completion rate of the samples is nozzle diameter > printing speed > fill rate. The predicted optimal printing parameters are a nozzle diameter of 0.6 mm, a printing speed of 767 mm/min, and a fill rate of 83%, with a predicted overall completion rate of the printed samples at 99.45%. Experimental validation revealed an actual overall completion rate of the printed samples at 99.52%, slightly higher than the predicted value. This discrepancy was attributed to the precision of the measurement methods and the variability in the printing process. The study demonstrates that the addition of astragalus polysaccharide significantly improves the 3D printing molding effect of wheat starch, and the printing parameter settings obtained by response surface optimization effectively enhance printing accuracy. This research provides experimental evidence and parameter optimization references for the application of non-starch polysaccharides in starch-based 3D food printing.

Effects of sodium alginate and rice variety on the physicochemical characteristics and 3D printing feasibility of rice paste

Resistant Starch Content and Physicochemical Properties of Non-Waxy Rice Starches Modified by Pullulanase, Heat-Moisture Treatment, and Citric Acid

Genetic Diversity of Amylose Content and RVA Pasting Parameters in 20 Rice Accessions Grown in Hainan, China.

Enhancing 3D Printing Accuracy of Cassava Starch Gel Through Temperature-Controlled Freezing

Research on rice starch gel preparation and crosslink network structure-rheological property based on direct-writing 3D printing

Effect of Starch Molecular Structure on Precision and Texture Properties of 3D Printed Products

3D Printing Properties of Heat-Induced Sodium Alginate-Whey Protein Isolate Edible Gel

Effect of Chlorella pyrenoidosa and Spirulina platensis powder on the physicochemical, structural, and rheological properties of rice starch: A comparative study

Physiochemical Properties of Rice with Contrasting Resistant Starch Content

Effects of Extrusion Technology on Physicochemical Properties and Microstructure of Rice Starch Added with Soy Protein Isolate and Whey Protein Isolate

Influence of sodium alginate on the gelatinization, rheological, and retrogradation properties of rice starch

Physicochemical properties and microstructural behaviors of rice starch/soy proteins mixtures at different proportions

The Effect of Different Milling Methods on the Physicochemical and In Vitro Digestibility of Rice Flour

Effects of Rice Straw Powder (RSP) Size and Pretreatment on Properties of FDM 3D-Printed RSP/Poly(lactic acid) Biocomposites

Structural and functional characterization of rice starch-based superabsorbent polymer materials

Effect of 3D printing accuracy by wheat starch gel combined with canola oil

Modification of rice starch using a combination of autoclaving and triple enzyme treatment: Structural, physicochemical and digestibility properties

Effects of Starch Molecular Structure and Physicochemical Properties on Eating Quality of Indica Rice with Similar Apparent Amylose and Protein Contents

How amylose molecular fine structure of rice starch affects functional properties

Effect of the Ratio of Soluble and Insoluble Dietary Fiber from Rice Bran with Extrusion Cooking Treatment on Pasting, Thermal, and Structural Properties of Rice Starch Gel

An Optimization Study of 3D Printing Technology Utilizing a Hybrid Gel System Based on Astragalus Polysaccharide and Wheat Starch