Abstract:This study reports about the dispersibility of short, straight and pristine multi-walled carbon nanotubes (pCNTs) in epoxy and their effectiveness on the mechanical properties of three-phased GF/epoxy/pCNT laminates. These nanotubes were produced by arc discharge method and had an average aspect ratio (l/d) of 100. Glass fibre-reinforced polymer samples with four different weight fractions of these nanotubes (0.5, 1.0, 1.5 and 2.0 wt.% of the total matrix system) were fabricated and tested for their thermo-mechanical and mechanical properties. These carbon nanotubes with small aspect ratio contributed well to the strengthening mechanism due to their homogeneous dispersion. Fractography revealed that these nanotubes formed aligned arrays that minimized entanglements between the individual tubes, thus leading to lesser agglomerates up to 1.5 wt.% of carbon nanotube loading. However, the samples modified with 2.0 wt.% of nanotubes had lesser individual tubes and more of their aggregates. Unmodified glass fibre-reinforced polymer samples had a glass transition temperature (T g ) of 139.2°C, whereas addition of 1.5 wt.% of multi-walled carbon nanotubes increased the same to 160°C. Similarly, these specimens witnessed about 21% and 34% enhancement in tensile and flexure strength over the control samples, respectively. However, these trends dropped at 2.0 wt.% carbon nanotube loading owing to nanotubes aggregation but were higher than those of the neat epoxy composite. Samples containing carbon nanotubes witnessed higher fatigue life which proves that multi-walled carbon nanotubes with smaller aspect ratio are capable of obstructing fatigue crack growth.

Load transfer and deformation mechanisms in carbon nanotube-polystyrene composites

Effective Enhancement of a Carbon Nanothread on the Mechanical Properties of the Polyethylene Nanocomposite

Sliding Behaviour of Carbon Nanothread Within a Bundle Embedded in Polymer Matrix

Influence of Inter-tube Connections on the Stress-Strain Behavior of Nanotube-Polymer Composites: Molecular Dynamics

Enhancement of pullout energy in a single-walled carbon nanotube-polyethylene composite system via auxetic effect

A study of mechanical behavior and morphology of carbon nanotube reinforced UHMWPE/Nylon 6 hybrid polymer nanocomposite fiber

Creep and Recovery of Polypropylene/Carbon Nanotube Composites

Resistance to Time-Dependent Deformation of Polystyrene/carbon Nanotube Composites under Cyclic Tension

Quantifying the interfacial load transfer in electrospun carbon nanotube polymer nanocomposite microfibers by using in situ Raman micromechanical characterization techniques

Carbon Nanotubes: Atomistic Investigation of Load Transfer Between DWNT Bundles “crosslinked” by PMMA Oligomers (adv. Funct. Mater. 15/2013)

Tensile Mechanical Behaviors of High Loading of Carbon Nanotube/Epoxy Composites via Experimental and Finite Element Analysis

The Effect of Nanotube Waviness and Agglomeration on the Elastic Property of Carbon Nanotube-Reinforced Composites

High-strength composite fibers: realizing true potential of carbon nanotubes in polymer matrix through continuous reticulate architecture and molecular level couplings.

Influence of carbon nanotubes on thermal expansion coefficient and thermal buckling of polymer composite plates: experimental and numerical investigations

DYNAMIC RHEOLOGICAL PROPERTIES OF POLYSTYRENE/MULTI-WALLED CARBON NANOTUBES COMPOSITES

Multiscale mechanics of the lateral pressure effect on enhancing the load transfer between polymer coated CNTs

Time-Concentration Superpositioning Principle Accounting for Reinforcement and Dissipation of Multi-Walled Carbon Nanotubes Filled Polystyrene Melts

The effect of the addition of carbon nanotube fluids to a polymeric matrix to produce simultaneous reinforcement and plasticization

Effectiveness of short and straight carbon nanotubes on dispersion state and static/dynamic mechanical properties of woven glass fibre-reinforced polymer laminates

Study of the structural defects on carbon nanotubes in metal matrix composites processed by severe plastic deformation