Abstract:Magnesium (Mg) and its alloys are one of the highly sought after structural material due to its lowest density among the structural material. Various attempts are being made by researchers to improve the mechanical performance of Mg alloys to widen their scope of application domains, especially in defence and biomedical sectors. On the development of Mg matrix composites, various works are reported on adding ceramic-based reinforcement which is proven to improve the strength of the material, but at the cost of ductility. With the research attempt on developing metallic reinforcement-based Mg composites being scarce, the scope of developing such composite material with superior strength and ductility is huge. Nickel has zero-solubility in Mg, high melting point and few closely matching lattice spacing with Mg crystal, which enabled simultaneous crystallization of Mg, with Ni acting as nucleation sites, and helped refining the microstructure. In the present research work, an attempt is made to incorporate 5 Wt.% of sub-micron-Ni particulate as reinforcement in developing an AZ31 matrix composite through stir casting route. A field emission scanning electron microscope and optical microscope was used to give the detailed analysis on the microstructural evaluation of the cast AZ31 alloy and the developed composite. Elemental mapping was done to confirm the uniform distribution of Ni particles throughout the magnesium matrix. The influence of reinforcement on the mechanical properties of the composites were investigated. The composite displayed improved properties when compared to the base alloy in terms of hardness, yield strength and ultimate tensile strength. The hardness of the composite was found to be 68.4HV, whereas the base alloy had a hardness of 53HV. The ultimate tensile strength (UTS) for the AZ31/Ni composite was greater than 50% when compared with the base alloy. Fractography study revealed the type of fracture of the base alloy and the composite.

Interface Engineering and Direct Observation of Strengthening Behavior in Field‐Sintered Boron Nitride Nanotube–Magnesium Alloy Composite

Enhanced thermal shock resistance of BN-based composites sintered by hot-pressing with the introduction of nano oxides

Synthesis, Microstructural Investigation, and Mechanical Behavior of AA5083/Boron Nitride Nanocomposite

Synthesis, mechanical properties, and microstructure of dual-matrix (DM) aluminum-boron nitride nanotube (Al-BNNT) composites

Manufacturing of Stereolithographic 3D Printed Boron Nitride Nanotube-Reinforced Ceramic Composites with Improved Thermal and Mechanical Performance

Cold‐Sprayed Boron‐Nitride‐Nanotube‐Reinforced Aluminum Matrix Composites with Improved Wear Resistance and Radiation Shielding

Carbon fibre-reinforced magnesium: Improvement of bending strength by nanodesign of boron nitride interlayers

Boron nitride nanosheets as precursors for 3D nano-configurations in titanium matrix composites: interfacial evolution and mechanical behavior

Protruding Boron Nitride Nanotubes on the Al2O3 Surface Enabled by Tannic Acid-Assisted Modification to Fabricate a Thermal Conductive Epoxy/Al2O3 Composite

Microstructure, Interface and Strengthening Mechanism of Ni-CNTs/AZ91 Magnesium Matrix Composites

Role of Nickel Particulate Reinforcement on Microstructure and Mechanical Performance of AZ31 Magnesium Composite

Mechanical Strength of Boron Nitride Nanotube-Polymer Interfaces

Microstructure, Mechanical, Tribological and Synergistic strengthening mechanisms of nickel/graphene nanoplatelets hybrid reinforced AZ91D magnesium-based matrix composites via spark plasma sintering

Microstructure and Strengthening Mechanism of Carbon Nanotubes Reinforced Magnesium Matrix Composite

Fabrication of Ni-coated carbon nanotubes reinforced magnesium matrix composites

Enhanced load transfer by designing mechanical interfacial bonding in carbon nanotube reinforced aluminum composites

Strengthening and Toughening Mechanisms of Mg Matrix Composites Reinforced with Specific Spatial Arrangement of In-Situ TiB2 Nanoparticles

Toughening and strengthening of Cu-coated carbon nanotubes reinforced AZ61 magnesium matrix nanocomposites by improving interfacial bonding

Enrichment in Fracture Ductility Tribological Characteristics of Magnesium-Based Nanocomposites Fabricated via Multi-pass Friction Stir Processing and Study of Significant Parameters

Mechanical Properties of Boron Nitride Nanotube Reinforced PEEK Composite: a Molecular Dynamics Study

Mechanical and thermal properties of in situ AlN/Al-12Si composite fabricated by laser powder bed fusion