Abstract:Statement of problem: Three-dimensional printing has the potential for clinical applications, and additive manufacturing materials for dental use merit further investigation. Purpose: The purpose of this in vitro study was to evaluate the properties of materials formulated with ethoxylated bisphenol A-dimethacrylate (Bis-EMA), urethane dimethacrylate (UDMA), and triethylene glycol dimethacrylate (TEGDMA) as 3D printing resins for ultraviolet digital light processing (UV-DLP) 3D printers and to characterize the mechanical and biological properties and accuracy of the printed objects. Material and methods: Ten different light-polymerized resins were formulated using Bis-EMA, UDMA, and TEGDMA. Their viscosities were measured, and only 7 resins with viscosities lower than 1500 centipoise (cP) were selected for 3D printing and further material characterization. The light-polymerized resins were printed into representative shapes using a custom-made 3D printer equipped with a 405-nm UV-DLP projector as the light source. The printed specimens were subjected to biologic, mechanical, and accuracy tests, and the data were submitted to 1-way ANOVA and Tukey post hoc comparisons (α=.05). Results: Photopolymerizable resins made of Bis-EMA, UDMA, and TEGDMA were successfully formulated for 3D printing to fabricate objects of various shapes and sizes. TEGDMA served as the diluent to reduce the viscosity and increase the degree of conversion, while UDMA and Bis-EMA provided strength as demonstrated by the mechanical testing. All the printed objects passed cytotoxicity testing. The flexural strengths of the printed specimens ranged between 60 MPa and 90 MPa; flexural modulus ranged between 1.7 GPa and 2.1 GPa; and surface hardness ranged between 14.5 HV and 24.6 HV. These represent similar mechanical properties to those of currently used clinical resin materials. In the accuracy test, the resin mixture composed of 80% Bis-EMA, 10% UDMA, and 10% TEGDMA had the highest accuracy, with a 0.051-mm deviation from the original design. Conclusions: Bis-EMA, UDMA, and TEGDMA are good candidates for the formulation of 3D printing resins for dental use. The printed objects demonstrated favorable biological and mechanical properties. Further, the accuracy of the printed specimens showed potential for clinical application.

Application of Bis[2-(3,4-epoxycyclohexyl)ethyl] octamethyltetrasiloxane in the Preparation of a Photosensitive Resin for Stereolithography 3D Printing

Preparation of a Novel Cationic Photosensitive Resin (3D-SLR01) for Stereolithography 3D Printing and Determination of Its Some Properties

Eugenol-Based Siloxane Acrylates for Ultraviolet-Curable Coatings and 3D Printing

Silicone–Epoxy‐Based Hybrid Photopolymers for 3D Printing

Acrylate-based photosensitive resin for stereolithographic three-dimensional printing

Aliphatic silicone‐epoxy based hybrid photopolymers applied in stereolithography 3D printing

Preparation and performance of silicone-modified 3D printing photosensitive materials

Synthesis and properties of a low-viscosity UV-curable oligomer for three-dimensional printing

Preparation withthe photosensitive resin for 3D printing stereolithography technique and study on its properties

Novel photosensitive resin simultaneously with outstanding cryogenic strength and toughness for digital light processing three-dimensional Printing

Urethane dimethacrylate-based photopolymerizable resins for stereolithography 3D printing: A physicochemical characterisation and biocompatibility evaluation

Branched Silicone Acrylates Enhanced Photocurable Epoxy Resins with High Strength, Toughness, and Low Dielectric Constant for SLA 3D Printing

Low Dielectric Constant Photocurable Fluorinated Poly (Phthalazinone Ether) Ink with Excellent Mechanical Properties and Heat Resistance

Preparation of isotropic tensile photosensitive resins for digital light processing 3D printing using orthogonal thiol-ene and thiol-epoxy dual-cured strategies

Mechanical properties, accuracy, and cytotoxicity of UV-polymerized 3D printing resins composed of Bis-EMA, UDMA, and TEGDMA

A Comparative Study on 3D Printed Silicone-Epoxy/acrylate Hybrid Polymers Via Pure Photopolymerization and Dual-Curing Mechanisms

Development of Bisphenol-A-Glycidyl-Methacrylate- and Trimethylolpropane-Triacrylate-Based Stereolithography 3D Printing Materials

Effect of functionality of diluents on digital light processing (DLP) based three‐dimensional (3D) printing of UV‐curable bisphenol A‐based epoxy acrylate resin

Exceptional Mechanical Properties and Heat Resistance of Photocurable Bismaleimide Ink for 3D Printing

Green Synthesis of Soybean Oil-Derived UV-Curable Resins for High-Resolution 3D Printing

Highly stretchable dual‐cure photosensitive resin for digital light processing printing