Abstract:In dissimilar friction stir welding (FSW), the weld nugget is composed of two elements, which are mechanically mixed. This microstructure helps enhance the mechanical properties when they are homogeneously mixed, and the particles are sub-micron in size. Therefore, it is important to understand the mechanism of the particle formation and their distribution for engineering the mechanical properties of the weld. In the present investigation, dissimilar FSW between commercial purity Al and Ti has been carried out. The weld nugget consisted of distributed Ti particles in an Al matrix. The distribution of the Ti particles in the weld nugget was characterized using X-ray micro-computed tomography (XCT). Microstructural evolution in Ti and Al was examined using a scanning electron microscope (SEM) equipped with an energy dispersive spectrometer (EDS), X-ray diffraction and electron back-scattered diffraction (EBSD). Hardness and tensile tests were carried out to determine the integrity of the welds. The XCT result shows that the weld nugget contains Ti particles of variable size. The finer particles of Ti are distributed homogeneously in the weld nugget, unlike large particles. The deformation mechanisms and microstructural evolution of the Ti interface and Al matrix are investigated using EBSD. It is observed that the microstructure of both Ti and Al is substantially refined. However, for a given grain in Al, the boundary is of mixed character, namely low- and high-angle boundaries. Hardness data of the weld indicate large variation within the nugget region. The tensile test sample revealed that the failure of the sample occurs on the Al side of the weld. The fractograph indicates ductile and brittle modes of fracture with a bimodal distribution of dimples at the surface. Lack of twining and fine grains (40 to 5 µm) at the Ti interface indicates high-temperature deformation. Deformation of Ti at low temperature and high strain rate is caused by adiabatic shear banding (ASB). In these shear bands, a high level of grain refinement is observed and is a path for easy crack propagation. It is proposed that the ASB-controlled deformation of Ti leads to a recrystallized microstructure at the interface and fragmentation of Ti. These Ti particles undergo further fragmentation to form smaller particles. On the other hand, microstructural evolution in Al is gradual because of the high stacking fault energy, which leads to continuous dynamic recrystallization (CDRX) through the dynamic recovery (DRV) mechanism. The mechanical properties of the weld depend on the characteristics of particles in the Al matrix. Proper control of the fragmentation and distribution of Ti particles and interface property can lead to superior mechanical properties of the weld.

Resistance Spot Welding of Similar and Dissimilar Metals: The Effect of Graphene Interlayer

Effect of graphene interlayer on resistance spot welded AISI-1008 steel joints

RESISTANCE SPOT WELDING OF DISSIMILAR METALS AISI 1006 LOW CARBON STEEL AND AA6061 ALUMINUM ALLOY USING ZINC AND TIN COATING

Feasibility study of resistance spot welding of dissimilar Al/Mg combinations with Ni based interlayers

Microstructure and tensile-shear behavior of dissimilar resistance spot welds between 2304 duplex stainless steel and Inconel 718 superalloy

Influence of Pin Offset and Weave Pattern on the Performance of Al-Cu Joints Reinforced with Graphene Particles

A Novel Dissimilar Resistance Spot Welding of Ti6Al4V Alloy and 316L Stainless Steel Via Copper As Interlayer by Using Optimal Electrodes

Microstructure and mechanical properties of resistance spot welded dissimilar aluminum/steel joints fabricated using high entropy alloy as interlayer

On the investigation of microstructure and mechanical properties of the AlCoCrFeNi 2.1 /316 L dissimilar spot-welded joint

Interfacial Microstructure and Mechanical Property of Dissimilar Resistance Spot Welded Joint of TC4 Titanium Alloy and 316L Stainless Steel with Nickel Interlayer

Resistance spot welding of high-strength DP steel and nano/ultrafine-grained IF steel sheets

On the Investigation of Microstructure and Mechanical Properties of the AlCoCrFeNi2.1/316 L Dissimilar Spot-Welded Joint

Characterization of Microstructure–Mechanical Properties Relationship in Dissimilar Resistance Spot Welding of the Advanced High-Strength Steel DP590 Steel to the Interstitial-Free Steel DC 06: EBSD Study

Comparative Investigation of Friction Stir Welds Reinforced with Graphene Nanoplatelets and Copper in AA6082-T6 Alloy

Dissimilar Resistance Spot Welding of DP 600/A5052/DP 600 Triple Sheets

Influence of Siliconized Zn-Graphene Oxide Complex Nanoparticles on the Microstructure and Mechanical Properties of AA5083: Focus on Gas Metal Arc Welding

The Effect of Welding Current and Electrode Force on the Heat Input, Weld Diameter, and Physical and Mechanical Properties of SS316L/Ti6Al4V Dissimilar Resistance Spot Welding with Aluminum Interlayer

Analyzing microstructural, residual stress, and mechanical characteristics in dissimilar welds of Inconel 59 and AISI 904L through double-pulsed gas metal arc welding

Multi-Length Scale Characterization of Microstructure Evolution and Its Consequence on Mechanical Properties in Dissimilar Friction Stir Welding of Titanium to Aluminum

Strengthening and toughening mechanisms in refilled friction stir spot welding of AA2014 aluminum alloy reinforced by graphene nanosheets

Comparative Analysis of Microstructure Evolution and Mechanical Properties of Dissimilar Welded Joints of AA7075/AA6061 via Friction Stir Welding, Tungsten Inert Gas Welding, and Tungsten Inert Gas + Friction Stir Processing