Abstract:Calcium phosphate cements present increased biocompatibility due to their chemical composition being similar to that of the hydroxyapatite in the hard tissues of the living body. It has certain limitations due to its poor mechanical properties, such as low tensile strength and increased brittleness. Thus, the optimal way to improve properties is through the design of novel composite cements. The purpose was fulfilled using a 25% hydroxyethyl methacrylate (HEMA) mixed with 3% urethane dimethacrzlate (UDMA) base matrix with various ratios of polyethylene glycol (PEG 400) and polycaprolactone (PCL). Mineral filler is based on tricalcium phosphate (TCP) with different chitosan ratio used as bio-response enhancer additive. Four mixtures were prepared: S0—unfilled polymer matrix; S1 with 50% TCP filler; S2 with 50% chitosan + TCP filler; and S3 with 17.5% chitosan + TCP mixed with 17.5% nano hydroxyapatite (HA). The mechanical properties testing revealed that the best compressive strength was obtained by S2, followed by S3, and the worst value was obtained for the unfilled matrix. The same tendency was observed for tensile and flexural strength. These results show that the novel filler system increases the mechanical resistance of the TCP composite cements. Liquid exposure investigation reveals a relative constant solubility of the used filler systems during 21 days of exposure: the most soluble fillers being S3 and S2 revealing that the additivated TCP is more soluble than without additives ones. Thus, the filler embedding mode into the polymer matrix plays a key role in the liquid absorption. It was observed that additive filler enhances the hydrophobicity of UDMA monomer, with the matrix resulting in the lowest liquid absorption values, while the non-additivated samples are more absorbent due to the prevalence of hydrolytic aliphatic groups within PEG 400. The higher liquid absorption was obtained on the first day of immersion, and it progressively decreased with exposure time due to the relative swelling of the surface microstructural features. The obtained results are confirmed by the microstructural changes monitored by SEM microscopy. S3 and S2 present a very uniform and compact filler distribution, while S1 presents local clustering of the TCP powder at the contact with the polymer matrix. The liquid exposure revealed significant pore formation in S0 and S1 samples, while S3 and S2 proved to be more resistant against superficial erosion, proving the best resistance against liquid penetration.

Porosity, Micro-Hardness and Morphology of White and Gray Portland Cements in Relation to Their Potential in the Development of New Dental Filling Materials

Effect of the Addition of Inorganic Fillers on the Properties of Degradable Polymeric Blends for Bone Tissue Engineering

Antibacterial and physical properties of resin cements containing MgO nanoparticles

Cellular differentiation, bioactive and mechanical properties of experimental light-curing pulp protection materials

Biocompatibility and osteogenic assessment of experimental fluoride-doped calcium-phosphate cements on human dental pulp stem cells

Characterization and chemical activity of Portland cement and two experimental cements with potential for use in dentistry

Obtaining bioceramic cements for dental repair procedures based on hydroxyapatite and bismuth oxide

Fluoride-containing nanoporous calcium-silicate MTA cements for endodontics and oral surgery: early fluorapatite formation in a phosphate-containing solution

Radiopacity of portland cement associated with different radiopacifying agents

Designing of porous PMMA/diopside bone cement for non-load bearing applications

Evaluation of remineralization potential and mechanical properties of pit and fissure sealants fortified with nano-hydroxyapatite and nano-amorphous calcium phosphate fillers: An in vitro study

In-depth polymerization of a self-adhesive dual-cured resin cement

Elucidation of real-time hardening mechanisms of two novel high-strength calcium phosphate bone cements

Inventive Microstructural and Durability Investigation of Cementitious Composites Involving Crystalline Waterproofing Admixtures and Portland Limestone Cement

Mechanical Properties and Liquid Absorption of Calcium Phosphate Composite Cements

Calcium Silicate and Calcium Hydroxide Materials for Pulp Capping: Biointeractivity, Porosity, Solubility and Bioactivity of Current Formulations

Mechanical Properties of Polymer-Infiltrated-ceramic (sodium Aluminum Silicate) Composites for Dental Restoration.

Mechanical Properties of Nano-Crystalline Glass-Carbomer Cements Used in Dentistry

The influence of different radiopacifying agents on the radiopacity, compressive strength, setting time, and porosity of Portland cement

Physical evaluation of a new pulp capping material developed from portland cement

Fabrication of macroporous apatite bone cements for non-load bearing orthopedic applications