Abstract:High efficiency, large capacity, and low energy consumption have become an important challenge in performances of post-combustion carbon dioxide (CO2) capture and regeneration. Blended absorbents have shown great potential but their process simulation, modeling, and optimization have not been known definitively. This work developed the blended aqueous absorbents based on piperazine (PZ) activators: PZ-activated methyldiethanolamine (MDEA), potassium carbonate solution (K2CO3), and aqueous ammonia (NH3H2O) to improve their techno-economic performances. The whole process simulation was conducted using a validated rate-based model under given a CO2 capture efficiency of 85%. In this process, the key factors including the molar concentration of the absorbent, PZ molar ratio, CO2 load of lean liquid, lean-liquid temperature, flue-gas temperature, and rich-liquid temperature, were employed for the design of experiment using response surface methodology. A series of nonlinear regression equations were developed using the flow rate of absorbents, the reboiler heat duty (in the units of gigajoules per ton of CO2), and the cooling-water flow rate as the multi-objective function. Subsequently, the optimal Pareto solution set and compromise solutions were determined using the multi-objective genetic algorithm and finally, their performances were assessed using the fuzzy close-degree algorithm. It was found that the optimal operating parameters can be determined effectively according to the proposed approach. For each PZ-activated blended absorbents, the trade-off effect exists between absorbent flow rate, reboiler heat duty, and cooling water consumption. The absorbents having optimal techno-economic performance were recommended to be PZ-activated MDEA, followed by PZ-activated K2CO3 and PZ-activated NH3H2O when considering the regeneration energy consumption. The results may provide a positive reference for process design and optimization of the industrial post-combustion CO2 capture system.

Modeling and validation of carbon dioxide absorption in aqueous solution of piperazine + methyldiethanolamine by PC-SAFT and E-NRTL models in a packed bed pilot plant: Study of kinetics and thermodynamics

Deciphering the Transfer Mechanisms for CO2 Absorption into Binary Blended Solutions

Assessment of carbon dioxide separation by amine solutions using electrolyte non-random two-liquid and Peng-Robinson models: Carbon dioxide absorption efficiency

Experimental Studies and Rate-Based Simulations of CO2 Absorption with Aqueous Ammonia and Piperazine Blended Solutions

Rate-Based Modelling and Simulation of Large-Scale CO2 Capture Using a Piperazine-Promoted Aqueous Ammonia Solution

Modelling and Process Analysis of Post-Combustion Carbon Capture with the Blend of 2-Amino-2-methyl-1-propanol and Piperazine

CO2 Capture Using Piperazine-Promoted, Aqueous Ammonia Solution: Rate-based Modelling and Process Simulation

Open access, thermodynamically consistent, electrolyte NRTL model for piperazine, AMP, water, CO 2 systems on Aspen Plus

Process Simulation for CO2 Capture with the Aqueous Solution of 1-Methylpiperazine and Its Mixture with Piperazine

Open Access, Thermodynamically Consistent, Electrolyte NRTL Model for Piperazine, AMP, Water, CO2 Systems on Aspen Plus

Experimental Studies And Rate-Based Process Simulations Of Co2 Absorption With Aqueous Ammonia Solutions

A Rigorous Model for Absorption of Carbon Dioxide into Aqueous N-Methyldiethanolamine Solution

Measurement and Thermodynamic Modeling for CO2 Solubility in the N-(2-Hydroxyethyl) Piperazine + Water System

Process simulation, optimization and assessment of post-combustion carbon dioxide capture with piperazine-activated blended absorbents

CO2 Solubility Measurement and Thermodynamic Modeling for 1-Methylpiperazine/water/co2

Thermodynamic Modeling of Piperazine/2-Aminomethylpropanol/Co2/Water

Kinetics region and model for mass transfer in carbon dioxide absorption into aqueous solution of 2-amino-2-methyl-1-propanol

Rate based modeling of absorption and regeneration for CO2 capture by aqueous ammonia solution

Modeling and Simulation of CO2 Capture Unit using Mixed Solvent of Aqueous Methyldiethanolamine and Piperazine for 6.4 MWe Power Plant

Bi-disperse Adsorption Model of the Performance of Amine Adsorbents for Direct Air Capture

Rate-Based Modelling and Validation of an Absorber and Stripper in an Amine-Based Post-Combustion CO2 Capture Process