Abstract:Additive manufacturing (AM) of biomedical materials provides enormous opportunities to fabricate multifunctional and structurally designed frameworks for tissue engineering, such as dental implants and bone substitutes. Despite several advantages of the binder jet 3D printing technology over other AM methods, for example, no limitations in materials selection, high materials recycling efficiency, no thermal stress development, no need to support materials, and the possibility of fabrication of printing functionally graded materials, the fabrication of biomedical-grade titanium alloys with high-density, fine microstructure, and low pickup of impurities is still challenging. This work presents the effects of powder particle size and 3D printing conditions on the microstructural features and mechanical properties of Ti-6Al-4V alloy. The formation of large and inter-aggregate pores during binder jetting is demonstrated and discussed. Design and selection of particle size distribution with a mean diameter of ~20 μm and large span and positive skewness are proposed to minimize binder-induced powder aggregation and fabricate green parts with a density of 65±1% PFD (pore-free density). Dilatometric studies under a partial pressure of argon (0.1 bar) determine that sintering just above the α/β transus temperature (~980 °C) provides a high strain rate to remove pores, but high-temperature sintering (≥1250 °C) is required to attain 97% PFD. The successful fabrication of high-density Ti-6Al-4V parts (≥96% PFD) with the microstructure comparable to metal injection molding (MIM) titanium parts (≈100 μm α grains + β lattes) is demonstrated. The tensile strength and elongation values fall in the range of 880±50 MPa and 6±2% (depending on the processing condition), which is comparable with metal injection molded parts and superior to the laser powder bed fusion technology concerning ductility. The content of carbon (<0.02 wt.%) and nitrogen (0.01 wt.%) also falls in the standard region of metal injection molding. However, oxygen pickup during sintering moderately increases the oxygen content (for 30–50%) over the standard level. The concentration of interstitials entrapped in the metal is comparable to that of parts manufactured by the powder bed fusion process, but the mechanical properties are better matched with the commercial titanium alloy. The fabrication of the titanium alloy as per the ASTM F2885 standard provides an excellent opportunity for the binder jetting process to develop custom-made biomaterials.

Binder Jetting 3D Printing of Titanium Aluminides Based Materials: A Feasibility Study

Printing of Titanium Implant Prototype

Microstructural development during additive manufacturing of biomedical grade Ti-6Al-4V alloy by three-dimensional binder jetting: material aspects and mechanical properties

Fabrication of Fully Dense Tial-Based Composite Sheets with A Novel Microlaminated Microstructure

Mechanical and Fatigue Properties of Ti-6Al-4V Alloy Fabricated Using Binder Jetting Process and Subjected to Hot Isostatic Pressing

Binder Jetting Additive Manufacturing of Inconel 718/TiC Metal Matrix Composites: Influence of TiC Content on Processing, Microstructure, Mechanical and Tribological Properties

Characterization of ceramic components fabricated using binder jetting additive manufacturing technology

Binder jet 3D printing—Process parameters, materials, properties, modeling, and challenges

Microstructure and Mechanical Properties of TiAl-based Composites Prepared by Stereolithography and Gelcasting Technologies

Microstructure and compression properties of 3D powder printed Ti-6Al-4V scaffolds with designed porosity: Experimental and computational analysis

Studies on Personalized Porous Titanium Implant Fabricated Using Three-dimensional Printing Forming Technique

Direct ink writing of porous Ti6Al4V alloys via UV light curing

Additive Manufacturing of Titanium-Based Materials Using Electron Beam Wire 3D Printing Approach: Peculiarities, Advantages, and Prospects

Influence of in situ ceramic reinforcement towards tailoring titanium matrix composites using laser-based additive manufacturing

3D ink-extrusion printing and sintering of Ti, Ti-TiB and Ti-TiC microlattices

Fabrication of Ti + Mg composites by three-dimensional printing of porous Ti and subsequent pressureless infiltration of biodegradable Mg

Investigating mechanical and surface porosity values of high-performing 3D-printed titanium alloys along with stress-relieving heat treatments

Effect of Process Parameters on the Microstructure and High-Temperature Strengths of Titanium Aluminide Alloy Fabricated by Electron Beam Melting

Fabrication of Porous Titanium Implants by Three-Dimensional Printing and Sintering at Different Temperatures.

A coupled thermo-mechanical material point model of binder jetted green part sintering

Hybrid Fabrication of Cold Metal Transfer Additive Manufacturing and Laser Metal Deposition for Ti6Al4V: The Microstructure and Dynamic/Static Mechanical Properties