Abstract:Wildhaber-Novikov gears are becoming more and more popular for heavy load applications. They have been tried as speed-reducing gears, in spite of heavy noise generation, in aircraft jet engines, marine engines and agricultural machinery. These circular-arc gears, though stronger than involute geras, have the disadvantage of needing larger face width. Axial face width required can be minimized only at the expense of load-carrying capacity. This is not a serious disadvantage with stationary engines. But in the case of automotive applications, this fact limits the load-carrying capacity of Wildhaber-Novikov gears, since space problem is very critical in these applications and large face widths, therefore, cannot be used for such gear-reduction units. The face width is determined by the helix angle and, therefore, a thorough investigation of the dependence of the load-carrying capacity on helix angle is necessary, if these special types of gears have to make headway into the automotive field.In this experimental investigation, three-dimensional photoelastic technique has been employed to study the load-carrying capacity/face width ratio. Three-dimensional gear models made of epoxy castings (Araldite B) were loaded in a specially built gear-loading fixture and were stress frozen. Gear cutters of Wildhaber-Novikov gears developed at the laboratory were used for the preparation of these three-dimensional gear models. The stress-frozen models were analyzed using the conventional slicing technique to study the contact and bending-stress distribution along the face width. The load-carrying capacity in terms of contact stress and bending stress has been studied for different face widths and helix angles.Twenty-deg pressure angle, 14-mm module gears of alladdendum type of Wildhaber-Novikov gears with different helix angles up to 40 deg were tested. The helical-overlap ratio used was 1.0. The conventional profile parameters were employed for the manufacture of gear cutters of end-mill type.The decrease in contact and bending strength with increase in the helix angle or decrease in the face width, as obtained from this photoelastic method of stress analysis has been compared with existing theoretical results.

Study on the quality and tooth root load carrying capacity of the high contact ratio asymmetrical gear tooth machined using WCEDM process

Experimental investigation on the surface quality of WEDM machined 20MnCr5 steel for Gear application

Optimizing Wire Electrical Discharge Machining Parameters for Enhanced Gear Machining Performance: A Machine Learning Approach on 20MnCr5 Steel

Fabrication of Micro Gear with Intact Tooth Profile by Micro Wire Electrical Discharge Machining

Tooth Profile Modification of Helical Gears and Experimental Study Based on Finite Element Contact Analysis

Multi-objective Optimization of Non-circular Gear Through Orthogonal Array and Fuzzy Comprehensive Evaluation Method in WEDM

A Comprehensive Investigation on Development of Lightweight Aluminium Miniature Gears by Thermoelectric Erosion Machining Process

Three-dimensional photoelastic study of the load-carrying capacity/face width ratio of Wildhaber-Novikov gears for automotive applications

Synthesis and Characterization of Mechanical Properties and Wire Cut EDM Process Parameters Analysis in AZ61 Magnesium Alloy + B4C + SiC

An Improved Modeling and Numerical Analysis Method for Tooth Surface Wear of Double-Arc Harmonic Gears

Complex taper profile machining of WC-Co composite using wire electric discharge process: analysis of geometrical accuracy, cutting rate, and surface quality

Analysis and Optimization of Tooth Surface Contact Stress of Gears with Tooth Profile Deviations, Meshing Errors and Lead Crowning Modifications Based on Finite Element Method and Taguchi Method

Static/dynamic Contact FEA and Experimental Study for Tooth Profile Modification of Helical Gears

Static/Dynamic Contact Finite Element Analysis for Tooth Profile Modification of Helical Gears

Analytical Calculation of the Tooth Surface Contact Stress of Cylindrical Gear with Variable Hyperbolic Circular-Arc-Tooth-Trace

A Novel Tooth Surface Modification Methodology for Wide-Faced Double-Helical Gear Pairs

Experimental and numerical investigations on the deformation defects by gear rolling process with local induction heating

NUMERICAL SIMULATION AND EXPERIMENTATION CUP-SHAPED THIN-WALLED INNER RECTANGULAR GEAR FORMED BY SPINNING

Study on the tooth profile and meshing equation of the anti-backlash double-roller enveloping hourglass worm with errors

Analysis on wear patterns and mechanisms of carbide tool for face-hobbing of spiral bevel gear

Computerized Investigation of Real Tooth Contact Analysis of Face-milled Spiral Bevel Gears