Abstract:Introduction. Over the last decade, composite materials based on polytetrafluoroethylene (PTFE) have been increasingly used as alternative materials for automotive applications. PTFE is characterized by a low coefficient of friction, hardness and corrosion resistance. However, this material has a high wear rate. A group of researchers attempted to improve the wear resistance of PTFE material by reinforcing it with different fillers. The purpose of the work: This study experimentally investigates the dry sliding wear characteristics of a PTFE composite reinforced with carbon fiber (35 wt.%) compared to SS304 stainless steel. In addition, experimental mathematical and ANN models are developed to predict the specific wear rate, taking into account the influence of pressure, sliding speed, and interface temperature. The methods of investigation. Dry sliding experiments were performed on a pin-on-disk wear testing machine with varying the normal load on the pin, disk rotation, and interface temperature. Experiments were planned systematically to investigate the effect of input parameters on specific wear rates with a wide range of design space. In total, fifteen experiments were carried out at a 5-kilometer distance without repeating the central run experiment. Sliding velocities were obtained by selecting the track diameter on the disk and corresponding rotation of the disk. A feedforward back-propagation machine learning algorithm was used to the ANN model. Results and Discussion. This study finds better prediction accuracy with the ANN architecture having two hidden layers with 150 neurons on each layer. This study finds an increase in specific wear rates with normal load, sliding velocity, and interface temperature. However, the increase is more prominent at higher process parameters. The normal load followed by sliding velocity most significantly affects the specific wear rate. The results predicted by the developed models for specific wear rates are in good agreement with the experimental values with an average error close to 10%. This shows that the model could be reliably used to obtain the wear rate of PTFE composite reinforced with carbon fiber (35 wt.%) compared to SS304 stainless steel. This study finds scope for further studies considering the effect of varying ANN architectures, different amount of neurons, and hidden layers on the prediction accuracy of the wear rate.

An energy-based model for the wear of unidirectional carbon fiber reinforced epoxy

An analytical approach to cutting force prediction in milling of carbon fiber reinforced polymer laminates

Modeling adhesive and abrasive wear phenomena in fretting interfaces: A multiphysics approach coupling friction energy, third body and contact oxygenation concepts

Dry Sliding Wear of Unidirectional Short Castor Oil Fiber Reinforced Epoxy Composite

Friction and Wear Behaviors of Surface-Modified Carbon Fabric/Epoxy Resin Composites

A mesoscopic model of mechanical erosion for the characterization of ablation behavior of C/C woven composites

Wear and Frictional Performance of Epoxy Composites Reinforced with Natural Waste Fibers and Fillers for Engineering Applications

Experimental and numerical investigations of wear behaviors of short-carbon-fiber reinforced polyetherimide composite

An Analytical Model of Mechanistic Wear of Polymers

A parameter-free mechanistic model of the adhesive wear process of rough surfaces in sliding contact

Micromechanics of material detachment during adhesive wear: A numerical assessment of Archard's wear model

Effect of reinforcement on wear debris of carbon nanofiber/high density polyethylene composites: Morphological study and quantitative analysis

Experimental investigation of wear of multiwalled carbon nanotube particles-filled poly-ether-ether-ketone matrix composites under dry sliding

An experimental and analytical approach to study the sliding wear performance of epoxy composites with steel wire and glass fiber reinforcement

Sliding wear characterization of epoxy composites filled with wood apple dust using Taguchi analysis and finite element method

Modeling of the Particle Abrasion Process and a Discrete Element Method Study of Its Shape Effect

Wear simulation of UHMWPE against the different counterface roughness in reciprocating unidirectional sliding motion

Energy Dissipation on an Elastic Interface as a Metric for Evaluating Three Friction Models

Modeling of sliding wear characteristics of Polytetrafluoroethylene (PTFE) composite reinforced with carbon fiber against SS304

Mesoscopic modeling of mechanical erosion for the ablation-erosion behavior of 3D C/C composites

Dynamic changes of mechanical properties induced by friction in the Archard wear model