Abstract:Ultra-high nickel single-crystal cathode materials have become the most promising for lithium-ion batteries. However, the preparation of ultra-high nickel single-crystal precursors by a continuous coprecipitation method has the disadvantages of large particle size, wide distribution, poor morphology. The extent of the inhomogeneous reactions can be more severe in single-crystal cathodes with larger particle size. Herein, the coprecipitation method with a solid concentrator was adopted, and citrate sodium was used as a complexing agent to improve the physical properties of precursors and electrochemical performance of single-crystal cathode materials. By analyzing the morphology and agglomeration mechanism of the precursor nucleuses under different pH values, it was found that hexagonal nanosheets grew along the 101 direction, and the primary particles showed thicker at pH of 11.4. The hexagonal nanosheets grew along the 001 direction, and the primary particles showed finer at pH of 12.2. The morphology and particle size uniformity of the secondary particles formed by agglomeration at these two pH values showed poor. However, hexagonal nanosheets grew synergistically along the 001 and 101 directions at pH of 11.8, so the primary particles with uniform particle size gradually agglomerated, and then the secondary particles with ultra-small particle size and uniform distribution obtained. Compared to materials prepared by the traditional continuous coprecipitation method, the precursor displays a smaller particle size(D50 = 1.8 µm), higher sphericity, uniformity and denser internal structure. In order to evaluate the performance of Ni0.94Co0.04Mn0.02(OH)2 with ultra-small particle size, the sintering conditions of LiNi0.94Co0.04Mn0.02O2 need to be explored. It was found that the LiNi0.94Co0.04Mn0.02O2 cathode material prepared at 790 °C exhibited higher discharge capacity, cycle and rate performance, compared to materials prepared at 760 °C and 820 °C. We further utilized TEM, EPMA, and XPS to test the internal structure and valence state of LiNi0.94Co0.04Mn0.02O2 cathode material. The results show that the LiNi0.94Co0.04Mn0.02O2 calcined at 790 °C has a good single crystal structure. The LiNi0.94Co0.04Mn0.02O2 cathode materials inherited the structure and particle size of Ni0.94Co0.04Mn0.02(OH)2 precursors, and displayed discharge capacity of 194.7 mAh/g and capacity retention rate of 89.8 % after 100 cycles at 1 C. The microstructure and phase transition of the as-prepared cathode material are well-maintained after long-term cycling, without obvious inter-crystalline micro-crack. The results indicate that its electrochemical performance is better than that of cathode materials with precursors prepared by a continuous coprecipitation method. This work provides new insights for the preparation of small-particle-size precursor and single-crystal cathode materials.

Preparation and electrochemical performance of LiNi0.5Mn1.5O4 spinels with different particle sizes and surface orientations as cathode materials for lithium-ion battery

Preparation of Submicrocrystal LiMn2O4 Used Mn3O4 As Precursor and Its Electrochemical Performance for Lithium Ion Battery

One-step Synthesis and Effect of Heat-Treatment on the Structure and Electrochemical Properties of LiNi0.5Mn1.5O4 Cathode Material for Lithium-Ion Batteries

Investigation on LiNi0.5Mn1.5O4 cathode material based on the precursor of nickel-manganese compound for lithium-ion battery

Electrochemical Performance Ni Doped Spinel LiMn2O4 Cathode for Lithium Ion Batteries

Electrochemical studies of spinel LiNi 0.5 Mn 1.5 O 4 cathodes with different particle morphologies

Physical properties and electrochemical performance of LiNi0.5Mn1.5O4 cathode material prepared by a coprecipitation method

Application of precursor with ultra-small particle size and uniform particle distribution for ultra-high nickel single-crystal cathode materials by coprecipitation method

Topotactic Phase Transformation of Lithiated Spinel to Layered LiMn0.5Ni0.5O2: The Interaction of 3-D and 2-D Li-ion Diffusion

Monitoring the morphology evolution of LiNi0.8Mn0.1Co0.1O2 during high-temperature solid state synthesis via in situ SEM

Synergistic Effect of Surface Plane and Particle Sizes on the Electrochemical Performance of LiNi0.5Mn1.5O4 Cathode Material Via a Facile Calcination Process

Controllable synthesis of spinel lithium nickel manganese oxide cathode material with enhanced electrochemical performances through a modified oxalate co-precipitation method

Improved Electrochemical Performance of 5 V Spinel LiNi 0 . 5 Mn 1 . 5 O 4 Microspheres by F-doping and Li 4 SiO 4 Coating

Synthetic Optimization and Electrochemical Properties of LiNi_(0.5)Mn_(0.5)O_2 Cathode Materials for Lithium-ion Batteries

Enhancing the Electrochemical Stability of LiNi0.8Co0.1Mn0.1O2 Compounds for Lithium-Ion Batteries via Tailoring Precursors Synthesis Temperatures

Synthesis and microstructure characterization of Li[Ni1/3Mn1/3Co1/3]O2for lithium ion batteries cathode

Influence of Synthetic Conditions on Structure and Electrochemical Performance of Li [ Ni1/3Co1/3Mn1/3 ] O2

Spray-drying method to synthesis LiMn1.5Ni0.5O4 and its electrochemical characteristics as a cathode material

Preparation of Spinel LiMn2O4 from Manganese Oxide and Its Electrochemical Performance

Effects of the Nb 2 O 5 -Modulated Surface on the Electrochemical Properties of Spinel LiMn 2 O 4 Cathodes

Role of Al-doping with Different Sites Upon the Structure and Electrochemical Performance of Spherical LiNi0.5Mn1.5O4 Cathode Materials for Lithium-Ion Batteries