Abstract:The major problem with quad flat no-lead package (QFN) packages is the delamination between the copper lead-frame and the molding compound (MC) due to relatively weak adhesion. The copper lead frame has excellent electrical and thermal conductivity. However, moisture penetration not only reduces the adhesion between the interfaces of the two materials, but also adversely affects the conductivity of Cu. Interface stratification is attributed to different material properties such as mismatch of coefficient of moisture expansion (CME), surface treatment of the mold pad, thermal strain, vapor pressure at high temperatures, and reduced interface strength due to moisture and temperature effects.The work presented in this paper focused on moisture, thermal and vapor pressure effects on the lead-frame and molding compound in the QFN during the precondition test and reflow process. The causes of delamination were examined both experimentally and via simulations. In an electronic package, the main failure effect stems from molding compound. To accurately simulate the moisture distribution in QFN, in this work, the moisture mechanism pertaining to material properties was investigated. This investigation focused on the MC and epoxy coefficient of moisture expansion and vapor pressure, and the parameters obtained by experimental study were incorporated into a simulation model to verify the fit between the experimental and the simulation findings. The electronic components employed in this work are standard for moisture sensitive testing, according to JEDEC J-STD-020D. To measure the specimen weight gain and geometric size, electronic balance and microscope were used, and these values were obtained under moisture sensitive level 1, level 2 and level 3 in order to establish the moisture desorption rate of the QFN package. And also according to the different degree of oxidation on the leadframe, the surface analysis of the material is carried out by environmental scanning electron microscope (ESEM) to understand the element distribution and interfacial strength. In addition, finite element analysis (FEA) was performed to analyze the stress, warpage and delamination in QFN packages. In this research will discuss the coupling forces of moisture, thermal stress and vapor pressure under MSL-3 and Reflow, and discuss the interface strength under different reliability test stages. To verify the accuracy of simulation modeling, the delamination site was observed and was aligned with the simulation results by applying scan acoustic tomography (SAT). Finally, the reliability of QFN was enhanced by investigating the moisture behavior of the materials co mprising the QFN.

Reliability Simulation with the Finite Element Analysis (FEA) of Redistribution Layer in Fan-out Wafer Level Packaging

Multiphysics Characterization of Polymer‐filled Through‐silicon Vias (pf‐tsvs) for Three‐dimensional Integration

Transient Electrothermal Analysis of Multilevel Interconnects in the Presence of ESD Pulses Using the Nonlinear Time-Domain Finite-Element Method

Selection and Characterization of Photosensitive Polyimide for Fan-Out Wafer-Level Packaging

Reliability Studies of Barrier Layers for Cu/PAE Low-K Interconnects.

Parameters study of thermomechanical reliability of board-level fan-out package

Finite element analysis of 2.5D packaging processes based on multi-physics field coupling for predicting the reliability of IC components

Investigation On Fbga Block Warpage By Finite Element Simulation

Reliability Assessment of Wafer Level Packages with Novel Feni under Bump Metallization

Analysis of warpage and reliability of very thin profile fine pitch ball grid array

Molding Compound Effects on Warpage of Fan-out Wafer Level Packaging

Thermal Cycling Test and Simulation of Fan-Out Chip-Last Panel-Level Packaging for Heterogeneous Integration

Comparison of Mechanical Modeling to Warpage Estimation of RDL-First Fan-Out Panel-Level Packaging

Overview of Finite-Element Analysis in Simulation of SiC Power Device Packaging

Development of Liquid, Granule and Sheet Type Epoxy Molding Compounds for Fan Out Wafer Level Package

Novel polymer design for ultra-low stress material for advanced packaging applications

Simulation and Analysis of Quad Flat No-lead Package (QFN) under Moisture, and Thermal Stress

Evaluation of the Effect of Stress Relief Slots on QFN Strip Warpage Using Finite Element Analysis

Warpage Analysis and Prediction of the Advanced Fan-Out Technology Based on Process Mechanics

Improvement of Thermo-Mechanical Reliability of Wafer-Level Chip Scale Packaging

A Polymer-Based Embedded Silicon Fan-Out Packaging (P-Esifo) Method for High-Density Chiplet Packaging