Abstract:The efficiency of fabricating an overhanging structure by selective laser melting (SLM) is an important indicator of the performance of metallic parts. This is due to the fact that defects such as warpage and adherent dross may occur during fabrication of the curved surfaces of overhanging structures. In order to investigate the optimum conditions for fabrication of the curved surfaces of the overhanging structures, experiments were carried out using 316-L stainless steel powder. Initially, the almost 100 % dense parts were fabricated. Then, a model that has a circular curved surface along the Z axis was designed. For a given fabrication depth of 25 μm, several overhanging structures were produced when the laser scanning energy input ranges from 0.15 to 0.6 J/mm. Results show that the upper surface of the almost 100 % dense cube fluctuates like ripples and that the fabrication quality of the curved surface of the overhanging structure varies greatly depending on the energy input and the obliquity angle. For a given energy input of 0.2 J/mm, the obliquity angle for fabricating a totally overhanging surface is as low as 30°. The warpage and adherent dross grow with an increase in the energy input and a decrease in the obliquity angle. Warpage may accumulate, and the accumulated warpage of many layers significantly exceeds the predetermined thickness of the layer. All the four overhanging structures fabricated using varying energy inputs have the following four zones: no dross surface, dense-sinking transition surface, totally sinking surface, and forming failure surface. In the overhanging structures, fabricated with varying laser energy parameters, the angle corresponding to each region was different. The quality of the overhanging surface can be improved by reducing the laser energy. Additionally, a better overhanging surface can be obtained by increasing the obliquity angle. The variation trend of the roughness Rz was almost the same as that of Ra, but the variation range of Rz was much larger than that of Ra. Finally, a foldable abacus with several curved-surface overhanging structures was fabricated to verify the research results. Fundamental methods for controlling and optimizing the SLM-based direct fabrication of curved surfaces of overhanging structures are proposed in this paper, from the perspectives of crafting and design.

Build Orientation Effect on Geometric Performance of Curved-Surface 316L Stainless Steel Parts Fabricated by Selective Laser Melting

Surface Quality of the Curved Overhanging Structure Manufactured from 316-L Stainless Steel by SLM

Effect of Processing Parameters and Build Orientation on Microstructure and Performance of AISI Stainless Steel 304L Made with Selective Laser Melting under Different Strain Rates

Theoretical and experimental study on surface roughness of 316L stainless steel metal parts obtained through selective laser melting

Effects of Inclination Angle on Surface Roughness and Corrosion Properties of Selective Laser Melted 316L Stainless Steel

Investigating the Relationship between Building Orientation and Surface Properties of Stainless Steel Prepared via Selective Laser Melting

Influence of Forming Directions on Surface Quality of 316L Produced by Selective Laser Melting Additive Manufacturing

Microstructure and Anisotropic Mechanical Properties of Selective Laser Melted Ti6Al4V Alloy under Different Scanning Strategies

Multi-Perspective Analysis of Building Orientation Effects on Microstructure, Mechanical and Surface Properties of SLM Ti6Al4V with Specific Geometry

Surface Roughness Control of Root Analogue Dental Implants Fabricated Using Selective Laser Melting

Compressive Mechanical Response and Microstructures in Low Strain Rate Plastic Deformation of Stainless Steel 316l Fabricated by Selective Laser Melting

Investigation into the effect of process parameters on density, surface roughness, and mechanical properties of 316L stainless steel fabricated by selective laser melting

The effect of process parameters and scanning strategies on surface roughness of stainless steel 316L SLM parts

Characteristics of Typical Geometrical Features Shaped by Selective Laser Melting

Influence of Build Angle and Polishing Roughness on Corrosion Resistance of 316L Stainless Steel Fabricated by SLM Method

Effect of Build Orientation on Mechanical Properties and Microstructure of Ti-6Al-4V Manufactured by Selective Laser Melting

Enhanced mechanical properties and formability of 316L stainless steel materials 3D-printed using selective laser melting

Mapping the roles of scan strategy and build orientation in predicting the crystallographic texture and yield strength of 316L stainless steel produced by laser powder bed fusion

A Comparative Analysis of Microstructural Variations in Horizontally and Vertically Built Planes of Selective Laser Melting-Fabricated 316L Stainless Steel in Comparison with Conventional 316L Stainless Steel

Effects of laying angles on stainless steel fabricated by selective laser melting

Experimental study on parameters optimization of selective laser melting 316L stainless steel based on response surface methodology