Abstract:As critical load-bearing components of aerospace equipment, thin-walled conical rings with inner transverse ribs (TWCRITR) are widely used for manufacturing rocket body, aircraft fuselage and space station shell et al., due to light weight, high strength and high load-bearing capacity. However, TWCRITR cannot be manufactured by traditional ring rolling (TRR), due to thin skin and high ribs. Aimed at this problem, a novel constraining ring rolling method (CRR) is proposed in this work to achieve the near-net-shape manufacturing of TWCRITR with high performance and efficiency. CRR innovatively uses a constraint roll and two baffles to fully constrain the diameter and height enlargement of ring, which ensures that the CRR process is still stable and the metal is enforced to flow axially to form high and wide ribs. Owing to the extreme geometry of TWCRITR and the complicated constraints of rolls in CRR of TWCRITR, the inherent relation between geometric and process parameters, stress state and metal flow is complicated, and it cannot be quantitatively determined by the FE simulation or experiment. Hence, the mechanical model which can determine the quantitative relation between geometric and process parameters, stress state and metal flow in CRR of TWCRITR is firstly established by using the slab method and upper bound method. Secondly, three new metal flow modes related with rib width in CRR of TWCRITR are found based on the established mechanical model. The first one is that the real-time height difference of two ribs slightly fluctuates and the two ribs almost grow synchronously when the width of two ribs is almost identical. The second one is that the rib with small width at the small end grows much faster than the rib with large width at the large end when the width difference of two ribs exceeds a critical value. The third one is that the rib with small width at the large end grows much faster than the rib with large width at the small end when the width difference of two ribs exceeds a critical value. Further, the quantitative relations between the metal flow resistance, divided-flow plane and rib growth under three metal flow modes are revealed theoretically, and consequently the mechanisms behind three metal flow modes in CRR of TWCRITR are clarified theoretically. Finally, the simulation and experiment for CRR of TWCRITR are conducted, and TWCRITR with 3 mm in skin thickness, 7 mm in rib width and 12.5 mm in rib height (the ratio of rib height to skin thickness is 4.16 and the ratio of rib width to skin thickness is 2.33) are stably rolled. Moreover, the roundness of rolled TWCRITR is good (it nearly approaches the inner surface roundness of constraint roll). The predicted values of rib height using the established mechanical model are in good accordance with the simulated and experimental ones, which validates the established mechanical model. Through analyzing the novel CRR process and complicated metal flow mechanisms, it is demonstrated that CRR is promising for manufacturing TWCRITR with high performance and efficiency.

An innovative radial envelope forming method for manufacturing thin-walled cylindrical ring with inner web ribs

Constraining ring rolling of thin-walled conical rings with transverse ribs

Research on Bending Forming Method of Large Diameter-Thickness Ratio Thin-Walled Tubes for Aerospace

Rolling of Cylindrical Parts with External Cross Ribs

A novel process for manufacturing large-diameter thin-walled metal ring: Double-roll pendulum hot rotary forging technology

Multi-pass rolling-extrusion of large-scale thin-walled square tube with longitudinal inner ribs

An innovative rotary rolling-forging process for manufacturing fork ring with extreme geometry

An innovative spinning-rolling process and its intelligent FE modelling for big-tapered profiled ring disk

Study on generating rolling method for manufacturing cylindrical parts with external cross ribs

Study of Dieless Radial Spinning for Thick-Walled Cylindrical Parts With External Grooves

Optimization of Mechanical Properties during Cold Rolling and Wrap-Forming for Metal Helical Tubes

Analytic model of outer rib height for thin-walled cylindrical rings in Spin-Extrusion Forming processing

Buckling Defect Optimization of Constrained Ring Rolling of Thin-Walled Conical Rings with Inner High Ribs Combining Response Surface Method with FEM

Study on the Ultrasonic-Assisted Spinning of Thin-Walled Cylindrical Parts with Longitudinal and Transverse Ribs

Enhancing radial strain uniformity of thin-walled cylinder by the dual asymmetric active counter-roller spinning process

Investigation on the inner hole spiral-groove of cross wedge rolling of hollow shafts with mandrel

Influence of Process Parameters on the Forming Results of Large-Sized Cylindrical Parts During Counter-Roller Spinning

Forming process chain for manufacturing complex conical-section profiled rings: On a co-design method

Research on plastic deformation transfer and distribution of large-diameter thin-walled metal ring parts in double-roll pendulum hot rotary forging process

Research on the Mechanism and Processability of Roll Forming

Design and simulation of cross wedge rolling process for hollow motor shaft