Abstract:The chemical-vapor-deposition (CVD) process is sufficiently well developed to allow the large-scale production of carbon nanotubes (CNTs). Metal nanoparticles (Fe, Co, Ni, etc.) are usually immobilized on a solid support and then decompose the gaseous hydrocarbon feedstocks into fragmented carbon units at elevated temperatures of 700-1100°C. Metal carbides are formed and then these dominate the growth of filamentous carbon as a structural template. The produced CNTs cannot stay firmly with an inert support and so inevitably detach away, especially during liquidphase purification or mechanical treatment. The biggest difficulties when handling the loose powder are filtration in the slurry-phase operations and the large pressure drops in fixed-bed reactors. These problems very much limit the application of CNTs on a large scale. The fabrication of carbon filaments on a structured support (e.g., activated carbon, carbon fibers, porous frameworks, graphite) has also suffered from discontinuities in the structure. The future use of CNTs has also been restricted by the technical requirements and the necessary high energy consumption to operate the intense and complicated CVD process. To avoid any mechanical post-treatment of powder and the risk of explosion during CVD synthesis, we have explored a simple method to produce monolithic CNTs directly as millimeter-scale spheres, featuring an integral continuity in the structure from microscopic to macroscopic scales. The whole process of CNTs growth has been conducted in a flow of ultrapure N2, involving a set of elementary steps in the solid phase being less complex than the widely used CVD process. The growth of CNTs is based on a solid reaction mechanism and well-graphitized nanotubes can be obtained even at a temperature as low as 400C. Direct observation of all growth events is made by using in-situ transmission electron microscopy (TEM), X-ray diffraction (XRD), IR, Raman spectroscopy and thermogravimetric analysis. A commercial styrene-divinylbenzene copolymer resin was used as the carbon precursor. According to Scheme 1, the ion-exchanged resin spheres were calcined at 800C in a flow of N2 or vacuum, after which the average diameter decreases from 0.77 to 0.49 mm, while the bulk density increases from 0.55 to 0.91 g ml. A novel macroscopic structure can be clearly seen, especially after the removal of the Fe nanoparticles and the amorphous carbon species by refluxing the spheres in concentrated HNO3. As seen in Fig. 1a, the twisted nanotubes construct the monolith while keeping a spherical shape. The cross-section views of the hand-broken spheres show no difference in the structure between the bulk and the surface, indicating a homogeneous distribution of the nanotubes in the millimeter-scale spheres (Fig. 1b). The nitrogen adsorption/ desorption isotherm shows a hysteresis loop to identify a typical mesoporous feature. The measured BET surface area and the pore volume are 223.7 m g and 0.42 ml g, respectively. The distribution of the pores ranges between about 2 and 15 nm.

A new method for preparing buckypaper by pressing a mixture of multi-walled carbon nanotubes and amorphous carbon

A pressurized filtration technique for fabricating carbon nanotube buckypaper: Structure, mechanical and conductive properties

Two-stage mechanical percolation in the epoxy resin intercalated buckypaper with high mechanical performance

Enhanced Mechanical and Electrical Properties of Carbon Nanotube Buckypaper by in Situ Cross-Linking

Freestanding Bucky Paper with High Strength from Multi-Wall Carbon Nanotubes

Buckypaper made with carbon nanotubes derived from CO2

Research Progress in Preparation of Buckypaper

A Molecular‐Level Interface Design Enabled High‐Strength and High‐Toughness Carbon Nanotube Buckypaper

High-density carbon nanotube buckypapers with superior transport and mechanical properties.

Highly Oriented Carbon Nanotube Papers Made of Aligned Carbon Nanotubes

Carbon Fiber/Carbon Nanotube Buckypaper Interply Hybrid Composites: Manufacturing Process and Tensile Properties

A New Route to Enhance the Packing Density of Buckypaper for Superior Piezoresistive Sensor Characteristics

A Pressure Enhanced Cvd Method for Large Scale Synthesis of Carbon Microtubes and Their Mechanical Properties

In-situ pressing synthesis of densely compacted carbon nanotubes reinforced nanocomposites with outstanding mechanical performance

Thermal Conductivity of Carbon/Boron Nitride Heteronanotube and Boron Nitride Nanotube Buckypapers: Implications for Thermal Management Composites

Surface coating of multi-walled carbon nanotube nanopaper on shape-memory polymer for multifunctionalization

Multi-Functional Properties of MWCNT/PVA Buckypapers Fabricated by Vacuum Filtration Combined with Hot Press: Thermal, Electrical and Electromagnetic Shielding

A New Strategy to Prepare Carbon Nanotube Thin Film by the Combination of Top-Down and Bottom-Up Approaches

Improvement on the Tensile Performance of Buckypaper Using a Novel Dispersant and Functionalized Carbon Nanotubes

Highly porous multiwalled carbon nanotube buckypaper using electrospun polyacrylonitrile nanofiber as a sacrificial material

Spherical Multi-Walled Carbon-Nanotube Architectures : Formation Mechanism and Catalytic Performance