Abstract:In this paper, SiCp aluminium matrix composites were used as the matrix, and AlSi10Mg powder, which has a relatively similar coefficient of thermal expansion to that of the matrix, was used to prepare laser cladding Al-based coatings. The results show that the optimal process parameters are P = 4400 W, Vf = 11.3 g·min−1, and VS = 1800 mm·min−1, and, although the hardness of the coatings is lower than the hardness of the substrate, it reduces the generation of defects such as cracks and porosity. With the increase in WC reinforced phase and the hardness of the coatings, wear resistance increases, the granular cytocrysts are transformed into rod-like cytocrysts, and at the same time generate the dendritic crystals, and the undergo grain refining and generate the new phases such as Al4C3, Al4SiC4. There is no obvious defect in AlSi10Mg + 40%WC coatings, the macro morphology of the coatings is good, there is no spalling in the friction wear morphology, and the wear resistance is excellent, but there are obvious cracks and obvious spalling in the coatings of AlSi10Mg + 60%WC. Compared to the matrix hardness of 171.61 HV, the hardness of the 20%WC cladding layer increased by a factor of 1.06, while the hardness of the 40%WC cladding layer increased by a factor of 1.65 and that of the 60%WC cladding layer increased by a factor of 1.8. In terms of wear, compared to a substrate wear amount of 9.36 mg, the wear for the 20%WC cladding layer was reduced to 6.13 mg (34.5% less than the substrate), for the 40%WC cladding layer it was reduced to 4.58 mg (51.06% less than the substrate), and for the 60%WC cladding layer it was reduced to 7.35 mg (21.47% less than the substrate). The quality of the coatings decreases although the hardness is higher than that of AlSi10Mg + 40%WC. The comprehensive performance of AlSi10Mg + 40%WC coatings is optimal.

Ceramic waste SiC particle-reinforced Al matrix composite brake materials with a high friction coefficient

Wear Behaviour and Microstructural Changes of SiCw-Al Composite under Unlubricated Sliding Friction

Tribological behavior of aluminum matrix composites reinforced with ceramic particulates in dry sliding against a semimetallic friction material

Modifying C/C–SiC brake pads with different Fe–Si alloy phases to improve the wear resistance of full-carbon/ceramic brake pair

Fading behavior and wear mechanisms of C/C–SiC brake disc during cyclic braking

Mechanical and tribological properties of C/C–SiC ceramic composites with different preforms

Effect of the pin temperature and SiC reinforcement on dry sliding tribological behavior of aluminium based silicon carbide metal matrix composite (Al-SiC) using Taguchi approach

Friction mechanism analysis of copper-based composites reinforced with ball-milled and modified composite ceramic powders

The Microstructure and Wear Characteristics of Cu–Fe Matrix Friction Material with Addition of SiC

Tribological performance and composition optimization of semi-metallic friction materials applied for carbon ceramic brake disc

Microstructure, mechanical and friction-wear properties of SiC-WC composite with Al and C as sintering aids

Silicon carbide whiskers enhance mechanical and anti-wear properties of PA6 towards potential applications in aerospace and automobile fields

Dry Sliding Wear And Static Immersion Corrosion Resistance of Aluminum Alloy 6061-T6/SiCp Metal Matrix Composite Prepared Via Friction Stir Processing

Fabrication and Process Optimization of Chinese Fir-Derived SiC Ceramic with High-Performance Friction Properties

Experimental Investigations on Microstructure, Mechanical and Wear Behavior Under Dry Sliding of Al6061 with Particulate-Reinforced SiC and TiB2 Metal Matrix Composite Developed by Stir Casting

Dry sliding wear and viscoelastic performance of aluminum-based hybrid composites reinforced with SiC and metallic glass particles

Enhanced braking performance of copper metal matrix composites incorporating fine mosaic pitch coke when mated with 30CrMnVA and C/C-SiC

Friction and Wear Mechanics of Fe-Based PM Pad Paired with Carbon Fiber-Reinforced Silicon Carbide (C/C-SiC) Disk Under High-Speed Braking

Effect of Spherical WC Content on the Microstructure and Properties of SiCp Aluminium Composite Material

The effect of alumina-based sintering aid on the microstructure, selected mechanical properties, and coefficient of friction of Cf/SiC composite prepared via spark plasma sintering (SPS) method

In-situ friction and wear study of SiCα/SiCβ and Al2O3-TiC-Co composite ceramics