Abstract:Purpose. Research of cutting force components during machining of high-hard cast iron by special prefabricated cutters with brazed niborite and ciborite inserts. Determination of the influence of geometric characteristics of the cutting tool, cutting modes and hardness of the material being machined on the cutting forces. The methods. The research methods were based on the fundamentals of cutting theory and cutting tools, material science properties of the tool and processed material. A research bench with special equipment was used. Findings. The nature of the change in the components of cutting forces with depth t, feed rate S and cutting speed v was experimentally investigated. The studies have shown an excess of the resulting force in the horizontal plane Pv over the circumferential one Pz, which is the main feature of turning high-hard metals. It has been established that the main limiting factors in the wear of tool cutting inserts are the permissible levels of forces. The hardness of HB has the greatest effect on the radial force Py. Under identical turning conditions for materials with a hardness of 220 to 610 HB, the forces Pz, Py and Px increase by 1,7; 3,3 and 2,3 times, respectively. In addition to the natural increase, the ratio of cutting forces also changes. Reducing the front angle of the blade causes a deterioration in chip formation conditions and leads to an increase in all components of the cutting forces. An increase in the radius at the top of the cutter r causes an increase in the width and decrease in the thickness of the layer to be cut, as well as a decrease in the main angle in the plan φr on the radial part of the blade. The originality. A complex dependence in the structural-stage form was obtained, which gives a clear picture of the influence of each parameter of the turning process on its performance. This dependence is a mathematical model for calculating the optimal operating and geometric parameters of the turning process of high-hard cast irons. The influence of the frontal angle γ, wear value h, and hardness of HB cast iron on the power characteristics during machining of high-hard cast irons has been studied. Practical implementation. It has been shown that it is economically advantageous to maximize the wear of cutting inserts made of relatively expensive composites. In this case, it is necessary to use a technological system of machine-workpiece-tool of high rigidity.

Study on Cutting Force, Cutting Temperature and Machining Residual Stress in Precision Turning of Pure Iron with Different Grain Sizes

Effect of grain size on subsurface characterization of pure iron subjected to orthogonal cutting

Finite Element Simulation Of High-Speed Cutting Alloy Cast Iron

Grain size influence on chip formation in high-speed machining of pure iron

Evaluation of Machining Parameters Affecting Cutting Forces in Dry Turning of GGG50 Ductile Cast Iron

Molecular Dynamics Simulation Study on the Influence of the Abrasive Flow Process on the Cutting of Iron-Carbon Alloys (α-Fe)

Formation mechanism of ultrafine grains at machined surface of 0.45 % carbon steel under high-speed turning process

Study on the surface grain state, residual stress and their influence on the deformation of thin-walled parts under ultra-precision cutting

Turning of 42CrMo4+QT under different scenarios: Dataset of machining, roughness and residual stress

Study of cutting forces during turning of high-hard cast irons

Comparison of Tool Wear, Surface Roughness, Cutting Forces, Tool Tip Temperature, and Chip Shape during Sustainable Turning of Bearing Steel

Influence of machining conditions on tool wear and surface characteristics in hot turning of AISI630 steel

Investigation on experiment and simulation of the grinding process of cast iron

Distinguishing effect of turning and grinding on the surface integrity and fatigue performance of ultra-high strength steel

Finite element simulation of residual stress in machining of Ti-6Al-4V with a microstructural consideration

Analysis, modelling, and optimization of force in ultra-precision hard turning of cold work hardened steel using the CBN tool

Influence of Lubricant Environment on Machined Surface Quality in Single-Point Diamond Turning of Ferrous Metal

Experimental Investigation on The Machinability Improvement in Magnetic-Field-Assisted Turning of Single-Crystal Copper

Experimental Investigation on the Machinability of PCBN Chamfered Tool in Dry Turning of Gray Cast Iron

Investigation of the effect of the cut parameter on the machining performance of PTFE cutting

Investigation of machinability in turning of PTFE based on MRR and cutting energy