Abstract:Laminated composites based on polyetheretherketone (PEEK) and polyimide (PI) matrices were fabricated by hot compression. Reinforcing materials (unidirectional carbon-fiber (CF) tapes or carbon fabric) and their layout patterns were varied. Stress–strain diagrams after three-point flexural tests were analyzed, and both lateral faces of the fractured specimens and fractured surfaces (obtained by optical and scanning electron microscopy, respectively) were studied. It was shown that the laminated composites possessed the maximum mechanical properties (flexural elastic modulus and strength) in the case of the unidirectional CF (0°/0°) layout. These composites were also not subjected to catastrophic failure during the tests. The PEEK-based composites showed twice the flexural strength of the PI-based ones (0.4 and 0.2 GPa, respectively), while the flexural modulus was four times higher (60 and 15 GPa, correspondently). The reason was associated with different melt flowability of the used polymer matrices and varied inter- (intra)layer adhesion levels. The effect of adhesion was additionally studied by computer simulation using a developed two-dimensional FE-model. It considered initial defects between the binder and CF, as well as subsequent delamination and failure under loads. Based on the developed FE-model, the influence of defects and delamination on the strength properties of the composites was shown at different stress states, and the corresponding quantitative estimates were reported. Moreover, another model was developed to determine the three-point flexural properties of the composites reinforced with CF and carbon fabric, taking into account different fiber layouts. It was shown within this model framework that the flexural strength of the studied composites could be increased by an order of magnitude by enhancing the adhesion level (considered through the contact area between CF and the binder).

Experimental investigations on flexural behaviour of delaminated carbon/epoxy composite using three dimensional digital image correlation

Delamination Analysis of Carbon Fiber/Epoxy Composite Laminates under Different Loading Rates Using Acoustic Emission

Experimental investigation on open-hole CFRP laminate under combined loading using acoustic emission and digital image correlation

Investigation of the Mode-I Delamination Behavior of Double-Double Laminate Carbon Fiber Reinforced Composite

Compressive Damage and Heat Release of Composite Laminate with Circular Prefabricated Defect, Part II-numerical Method

Post-Buckling Response of Carbon/Epoxy Laminates with Delamination under Quasi-Static Compression: Experiments and Numerical Simulations

In situ characterization of the flexural behavior and failure mechanism of 2D needle-punched carbon/carbon composites by digital image correlation

Progressive failure simulation of angled composite beams subject to flexural loading

Damage monitoring of glass/epoxy-curved laminates with different stacking sequences using acoustic emission

Three-dimensional In-Situ Observation and Cohesive Zone Modeling of Tension-Induced Delamination of Two-Dimensional C/SiC Composites Via Deep Learning-Based Damage Identification

Delamination in Carbon Fiber Epoxy DCB Laminates with Different Stacking Sequences: R-curve Behavior and Bridging Traction-Separation Relation

Integrated XFEM-CE Analysis of Delamination Migration in Multi-Directional Composite Laminates

An analytical and experimental study of the nonlinear behaviour of a carbon/epoxy under a three-point bending test

Layer-wise damage prediction in carbon/Kevlar/S-glass/E-glass fibre reinforced epoxy hybrid composites under low-velocity impact loading using advanced 3D computed tomography

Deformation Behavior and Fracture Patterns of Laminated PEEK- and PI-Based Composites with Various Carbon-Fiber Reinforcement

A comprehensive experimental investigation of the rate-dependent interlaminar delamination behaviour of CFRP composites

Study of Structural Composite Joint Damage by the Digital Image Correlation

A Study on the Intralaminar Damage and Interlaminar Delamination of Carbon Fiber Composite Laminates under Three-Point Bending Using Acoustic Emission

Effect of (0°/90°) and (+45°/–45°) plies position on the failure modes and acoustic signals in carbon fiber reinforced polymer laminates under quasi-static tensile loading

Ultrasound investigation of pseudo-ductility of carbon fiber reinforced polymers at ± 45° layup

The Compressive Behavior of CFRP Laminates with Delamination of Different Shapes Using Numerical and Experimental Approaches