Abstract:The 2010 emission standards for heavy-duty diesel engines in the U.S. have established a limit for oxides of nitrogen (NOx) emissions of 0.20 g/bhp-hr., a 90% reduction from the previous emission standards. However, it has been projected that even when the entire on-road fleet of heavy-duty vehicles operating in California is compliant with the 2010 emission standards, the upcoming National Ambient Air Quality Standards (NAAQS) requirement for ambient particulate matter and ozone will not be achieved in California without further significant reductions in NOx emissions from the heavy-duty vehicle fleet. Given this, there is potential of further reduction in NOx emissions limit standards for heavy duty engines in the US. Recently there have been extensive studies and publications focusing on ultra-low NOx after treatment technologies that help achieve up to 0.02g/bhp-hr. at tailpipe [1]. To achieve ultra-low NOx emission levels over the composite HD FTP cycle, rapid heat energy must be provided to the diesel exhaust after-treatment system during cold start portion of the cycle, and peak NOx reduction efficiency must be maintained during the hot-start portion of cycle. Delivering this has been the challenge for conventional four-stroke heavy duty diesel engines as these are competing demands. Ultra-low NOx system solutions involving the implementation of supplemental heat sources downstream in the exhaust system comes at CO2 penalty and adds significant cost and complexity. The Achates Power Opposed-Piston Engine design provides an ideal solution to this challenge. The opposed-piston engine has several inherent advantages over conventional four-stroke engines, like higher BTE [2], low BMEP and internal EGR facilitating low engine out NOx and ability to provide rapid engine out temperature rise [3] for emission system while maintaining low engine out NOx. This paper highlights the results from cold-start HD FTP testing with the 4.9L Opposed-Piston Engine. The target of this testing was to evaluate the ability of the Achates Power Opposed-Piston Engine to provide rapid engine out temperature rise by operating the engine in the mode designed to deliver exhaust enthalpy, aiding fast catalyst light-off which enables early and peak NOx conversion in the exhaust after treatment system. Rapid exhaust heat and temperature rise that was delivered exceeded SCR catalyst light-off temperature thresholds (200°C) within the first 40 seconds in the cycle while controlling the engine out NOx levels.

HD diesel engine – exhaust gas temperature management and advanced exhaust gas aftertreatment technology for ultra-low NOx emission legislation

Fuel Consumption and Emission Reduction for Non-Road Diesel Engines with Electrically Heated Catalysts

Robust, Model-Based Urea Dosing Control for SCR Aftertreatment Systems using a Cross-Sensitive Tailpipe NOx Sensor

Data-Based On-Board Diagnostics for Diesel Engine NOx-Reduction Aftertreatment Systems

Cold Start HD FTP Test Results on Multi-Cylinder Opposed-Piston Engine Demonstrating Rapid Exhaust Enthalpy Rise to Achieve Ultra Low NOx

Diesel Engine 2-Stroke Breathing for Aftertreatment Warm-Up

Methodology of diesel particulate filter testing on test bed for non-road engine application

Mitigation of PAH and nitro-PAH emissions from nonroad diesel engines

Emission behaviour and aftertreatment of stationary and transient operated hydrogen engines

Experimental Study of Aftertreatment System Configurations for Euro Ⅵ Heavy-Duty Diesel Engines

Experimental investigation of urea injection strategy for close-coupled SCR aftertreatment system to meet ultra-low NO<i><sub>x</sub></i> emission regulation

Recent Advances in SCR Systems of Heavy-Duty Diesel Vehicles—Low-Temperature NOx Reduction Technology and Combination of SCR with Remote OBD

Effect of late diesel injection on close-coupled SCR + ASC during DPF regeneration period

Study on Selection of Diesel Engine Exhaust After-Treatment System Materials and Emission Performance for Genset Applications

Application of Nox-SCR Aftertreatment System to the HD Diesel Engine Using Ethanol As a Reductant

Diesel Engine SCR Control: Current Development and Future Challenges

Evaluation of thermal management technologies for fuel efficient cold-start emissions reduction in diesel engines

Review on Selective Catalytic Reduction Technology of Diesel Engines

Integrated catalytic systems for simultaneous NOx and PM reduction: a comprehensive evaluation of synergistic performance and combustion waste energy utilization

Lean-Burn Natural Gas Engines: Challenges and Concepts for an Efficient Exhaust Gas Aftertreatment System

Burner based thermal management approach utilizing in-exhaust burner technology with a CDA equipped engine